- 您現在的位置：買賣IC網 > PDF目錄9756 > 78P2352-IGTR/F (Maxim Integrated Products)IC LIU SDH SONET 2CH 128-LQFP PDF資料下載
參數資料
| 型號： | 78P2352-IGTR/F |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 26/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU SDH SONET 2CH 128-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 2/2 |
| 規程： | E4，OC-3，STM1-E |
| 電源電壓： | 3.15 V ~ 3.45 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP 裸露焊盤 |
| 供應商設備封裝： | 128-LQFP-EP（14x14） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
78P2352
Dual Channel
OC-3/ STM1-E/ E4 LIU
Page: 32 of 42
2006 Teridian Semiconductor Corporation
Rev. 2.4
(Note 1)
0.60
0.55
0.50
0.45
0.40
0.05
-0.05
-0.50
-0.55
-0.60
-0.45
-0.40
(Note 1)
Nominal
Zero Level
(Note 2)
6.43ns
0.1ns
1ns
1.608ns
1ns
Nominal
Pulse
V
3.215ns
1.2ns
3.215ns
1.608ns
1ns
0.5ns
Note 1 – The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall into
the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more than
0.05V.
Note 2 – For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01
F, to the input of
the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input
signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any
such adjustment should be the same for both masks and should not exceed
±0.05V. This may be checked by removing the input signal again
and verifying that the trace lies with
±0.05V of the nominal zero level of the masks.
Note 3 – Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or
succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish
edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing
signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the mask,
it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be accomplished by
several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope and the pulse output
circuits with the same clock signal].
Note 4 – For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed
2ns.
Note 5 –The inverse pulse will have the same characteristics, noting that the timing tolerance at the level of the negative and positive
transitions are
± 0.1ns and ±0.5ns respectively.
Figure 14 – Mask of a Pulse corresponding to a binary One in STS-3/STM-1 mode
相關PDF資料 |
PDF描述 |
|---|---|
| VE-26V-IU-F3 | CONVERTER MOD DC/DC 5.8V 200W |
| MC100EP16FDG | IC RCVR/DRVR ECL DIFF 5V 8SOIC |
| DS26303L-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| MS27474E14B15P | CONN RCPT 15POS JAM NUT W/PINS |
| D38999/26FH55PA | CONN PLUG 55POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 78P236-IP | 制造商:SSI 功能描述: |
| 78P47404T15 | 制造商:n/a 功能描述:0.47MFD 400VDC caps |
| 78P7200 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Line Interface Unit |
| 78P7200IH | 制造商:TDK CORPORATION OF AMERICA 功能描述:Line Interface 28-Pin PLCC |
| 78P7200-IH | 制造商:TDK 功能描述:Line Interface 28-Pin PLCC |
發布緊急采購，3分鐘左右您將得到回復。