- 您現在的位置：買賣IC網 > PDF目錄368740 > 1977IFE (Linear Technology Corporation) High Voltage 1.5A, 500kHz Step-Down Switching Regulator with 100uA Quiescent Current PDF資料下載
參數資料
| 型號： | 1977IFE |
| 廠商： | Linear Technology Corporation |
| 英文描述： | High Voltage 1.5A, 500kHz Step-Down Switching Regulator with 100uA Quiescent Current |
| 中文描述： | 高電壓，500kHz降壓1.5安培的電流型開關穩壓器的靜態電流為100uA |
| 文件頁數： | 7/24頁 |
| 文件大小： | 288K |
| 代理商： | 1977IFE |
LT1977
7
1977f
PIU
voltage on the PGFB pin drops below V
PGFB
, C
CT
will be
discharged rapidly to 0V and PG will be active low with a
200
μ
A sink capability. If the C
T
pin is clamped (Power Good
condition) during normal operation and SHDN is taken low,
the C
T
pin will be discharged and a delay period will occur
when SHDN is returned high. See the Power Good section
in Applications Information for details.
GND (Pins 8, 17):
The GND pin connection acts as the
reference for the regulated output, so load regulation will
suffer if the “ground” end of the load is not at the same
voltage as the GND pin of the IC. This condition will occur
when load current or other currents flow through metal
paths between the GND pin and the load ground. Keep the
path between the GND pin and the load ground short and
use a ground plane when possible. The GND pin also acts
as a heat sink and should be soldered (along with the
exposed leadframe) to the copper ground plane to reduce
thermal resistance (see Applications Information).
C
SS
(Pin 9):
A capacitor from the C
SS
pin to the regulated
output voltage determines the output voltage ramp rate
during start-up. When the current through the C
SS
capaci-
tor exceeds the C
SS
threshold (I
CSS
), the voltage ramp of
the output is limited. The C
SS
threshold is proportional to
the FB voltage (see Typical Performance Characteristics)
and is defeated for FB voltage greater than 0.9V (typical).
See Soft-Start section in Applications Information for
details.
BIAS (Pin 10):
The BIAS pin is used to improve efficiency
when operating at higher input voltages and light load
current. Connecting this pin to the regulated output volt-
age forces most of the internal circuitry to draw its
operating current from the output voltage rather than the
input supply. This architecture increases efficiency espe-
cially when the input voltage is much higher than the
output. Minimum output voltage setting for this mode of
operation is 3V.
V
C
(Pin 11):
The V
C
pin is the output of the error amplifier
and the input of the peak switch current comparator. It is
normally used for frequency compensation, but can also
serve as a current clamp or control loop override. V
C
sits
at about 0.45V for light loads and 2.2V at maximum load.
During the sleep portion of Burst Mode operation, the V
C
pin is held at a voltage slightly below the burst threshold
for better transient response. Driving the V
C
pin to ground
will disable switching and place the IC into sleep mode.
FB (Pin 12):
The feedback pin is used to determine the
output voltage using an external voltage divider from the
output that generates 1.25V at the FB pin . When the FB pin
drops below 0.9V, switching frequency is reduced, the
SYNC function is disabled and output ramp rate control is
enabled via the C
SS
pin. See the Feedback section in
Applications Information for details.
PGFB (PIN 13):
The PGFB pin is the positive input to a
comparator whose negative input is set at V
PGFB
. When
PGFB is taken above V
PGFB
, current (I
CSS
) is sourced into
the C
T
pin starting the PG delay period. When the voltage
on the PGFB pin drops below V
PGFB
, the C
T
pin is rapidly
discharged resetting the PG delay period. The PGFB volt-
age is typically generated by a resistive divider from the
regulated output or input supply. See Power Good section
in Applications Information for details.
SYNC (Pin 14):
The SYNC pin is used to synchronize the
internal oscillator to an external signal. It is directly logic
compatible and can be driven with any signal between
30% and 70% duty cycle. The synchronizing range is
equal to maximum initial operating frequency up to 700kHz.
When the voltage on the FB pin is below 0.9V the SYNC
function is disabled. See the Synchronizing section in
Applications Information for details.
SHDN (Pin 15):
The SHDN pin is used to turn off the
regulator and to reduce input current to less than 1
μ
A. The
SHDN pin requires a voltage above 1.2V with a typical
source current of 3
μ
A to take the IC out of the shutdown
state.
PG (Pin 16):
The PG pin is functional only when the SHDN
pin is above its threshold, and is active low when the
internal clamp on the C
T
pin is below its clamp level and
high impedance when the clamp is active. The PG pin has
a typical sink capability of 200
μ
A. See the Power Good
section in Applications Information for details.
相關PDF資料 |
PDF描述 |
|---|---|
| 1982995-1 | Pluggable Bus Bar Connectors & Sockets |
| 19MT050XF | FULL BRIDGE FREDFET MTP HEXFET POWER MOSFET |
| 19TQ015S | SCHOTTKY RECTIFIER |
| 19U200PG1K | Pressure Sensors Low-Cost, Stainless Steel, Isolated Sensors |
| 19U050PA4K | Pressure Sensors Low-Cost, Stainless Steel, Isolated Sensors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1977-XX-XXX | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:1977 Series High Frequency Coaxial SPD |
| 1978 | 功能描述:電池組 RECHARGEABLE BATTRY PACK RoHS:否 制造商:Ultralife 電池大小: 電池數量: 輸出電壓:3.7 V 容量: 化學性質:Lithium 端接類型:Wire |
| 19780 | 功能描述:KIT METER RES DIG TEMP/HUMIDITY RoHS:否 類別:靜電控制，ESD，無塵室產品 >> 監視器，測試儀 系列:- 產品目錄繪圖:19226 標準包裝:1 系列:- 類型:工作站監視器 使用:工作面，腕帶監視 特點:連續監視，NIST 可追溯，單芯系統 電源類型:AC 適配器 包括:AC 適配器，證書，軟線，五金件 其它名稱:16-1116 |
| 19-780 | 制造商:GC Electronics 功能描述:Squeeze Bottle Dispense Solvents In The Required Amounts In The Proper Location |
| 1978000000 | 制造商:Weidmuller 功能描述:SC-SMT 3.81/09/135G 1.5SN BK |
發布緊急采購，3分鐘左右您將得到回復。