- 您現在的位置：買賣IC網 > PDF目錄376463 > XRT83VSH314 (Exar Corporation) 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT83VSH314 |
| 廠商： | Exar Corporation |
| 英文描述： | 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| 中文描述： | 14-CHANNEL的T1/E1/J1短途線路接口單元 |
| 文件頁數： | 26/80頁 |
| 文件大?。?/td> | 497K |
| 代理商： | XRT83VSH314 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
XRT83VSH314
23
14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.1
3.3
The jitter attenuator reduces phase and frequency jitter in the recovered clock if it is selected in the receive
path. The jitter attenuator uses a data FIFO (First In First Out) with a programmable depth of 32-bit or 64-bit. If
the LIU is used for line synchronization (loop timing systems), the JA should be enabled in the receive path.
When the Read and Write pointers of the FIFO are within 2-Bits of over-flowing or under-flowing, the bandwidth
of the jitter attenuator is widened to track the short term input jitter, thereby avoiding data corruption. When this
condition occurs, the jitter attenuator will not attenuate input jitter until the Read/Write pointer’s position is
outside the 2-Bit window. In T1 mode, the bandwidth of the JA is always set to 3Hz. In E1 mode, the
bandwidth is programmable to either 10Hz or 1.5Hz (1.5Hz automatically selects the 64-Bit FIFO depth). The
JA has a clock delay equal to of the FIFO bit depth.
Jitter Attenuator
N
OTE
:
If the LIU is used in a multiplexer/mapper application where stuffing bits are typically removed, the jitter attenuator
can be selected in the transmit path to smooth out the gapped clock. See the Transmit Section of this datasheet.
3.4
HDB3/B8ZS Decoder
In single rail mode, RPOS can decode AMI or HDB3/B8ZS signals. For E1 mode, HDB3 is defined as any
block of 4 successive zeros replaced with 000V or B00V, so that two successive V pulses are of opposite
polarity to prevent a DC component. In T1 mode, 8 successive zeros are replaced with 000VB0VB. If the
HDB3/B8ZS decoder is selected, the receive path removes the V and B pulses so that the original data is
output to RPOS.
3.4.0.1
RPOS/RNEG/RCLK
The digital output data can be programmed to either single rail or dual rail formats.
Figure 10
is a timing
diagram of a repeating "0011" pattern in single-rail mode.
Figure 11
is a timing diagram of the same fixed
pattern in dual rail mode.
F
IGURE
10. S
INGLE
R
AIL
M
ODE
W
ITH
A
F
IXED
R
EPEATING
"0011" P
ATTERN
F
IGURE
11. D
UAL
R
AIL
M
ODE
W
ITH
A
F
IXED
R
EPEATING
"0011" P
ATTERN
RCLK
RPOS
0
0
0
1
1
RCLK
RPOS
0
0
0
1
1
RNEG
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83VSH314IB | 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH316 | 16-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH316IB | 16-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH38 | 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH38IB | 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83VSH314ES | 功能描述:外圍驅動器與原件 - PCI 14 CHT1/E1LIUSH LOW COST VERSION RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83VSH314IB | 功能描述:接口 - 專用 14 CH, SH T1/E1 1.8V DGTL/3.3V ANLG RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| XRT83VSH314IB-F | 功能描述:外圍驅動器與原件 - PCI 14 Channel Short-Haul RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83VSH314IB-SAM | 制造商:Exar Corporation 功能描述:FOR FUJITSU ONLY |
| XRT83VSH316 | 制造商:EXAR 制造商全稱:EXAR 功能描述:16-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。