- 您現在的位置：買賣IC網 > PDF目錄376463 > XRT83SH38 (Exar Corporation) 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT83SH38 |
| 廠商： | Exar Corporation |
| 英文描述： | 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| 中文描述： | 8通道的T1/E1/J1短途線路接口單元 |
| 文件頁數： | 50/78頁 |
| 文件大?。?/td> | 606K |
| 代理商： | XRT83SH38 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
XRT83SH38
47
8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.7
6.4
Intel Mode Programmed I/O Access (Asynchronous)
If the LIU is interfaced to an Intel type μP, then it should be configured to operate in the Intel mode. Intel type
Read and Write operations are described below.
Intel Mode Read Cycle
Whenever an Intel-type μP wishes to read the contents of a register, it should do the following.
1.
Place the address of the target register on the address bus input pins ADDR[7:0].
2.
While the μP is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables further communication between the
μP and the LIU microprocessor interface block.
3.
Toggle the ALE input pin "High". This step enables the address bus input drivers, within the microproces-
sor interface block of the LIU.
4.
The μP should then toggle the ALE pin "Low". This step causes the LIU to latch the contents of the address
bus into its internal circuitry. At this point, the address of the register has now been selected.
5.
Next, the μP should indicate that this current bus cycle is a Read operation by toggling the RD input pin
"Low". This action also enables the bi-directional data bus output drivers of the LIU.
6.
After the μP toggles the Read signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
in order to inform the μP that the data is available to be read by the μP, and that it is ready for the next com-
mand.
7.
After the μP detects the RDY signal and has read the data, it can terminate the Read Cycle by toggling the
RD input pin "High".
N
OTE
:
ALE can be tied “High” if this signal is not available.
The Intel Mode Write Cycle
Whenever an Intel type μP wishes to write a byte or word of data into a register within the LIU, it should do the
following.
1.
Place the address of the target register on the address bus input pins ADDR[7:0].
2.
While the μP is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables further communication between the
μP and the LIU microprocessor interface block.
3.
Toggle the ALE input pin "High". This step enables the address bus input drivers, within the microproces-
sor interface block of the LIU.
4.
The μP should then toggle the ALE pin "Low". This step causes the LIU to latch the contents of the address
bus into its internal circuitry. At this point, the address of the register has now been selected.
5.
The μP should then place the byte or word that it intends to write into the target register, on the bi-direc-
tional data bus DATA[7:0].
6.
Next, the μP should indicate that this current bus cycle is a Write operation by toggling the
WR
input pin
"Low". This action also enables the bi-directional data bus input drivers of the LIU.
7.
After the μP toggles the Write signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
in order to inform the μP that the data has been written into the internal register location, and that it is ready
for the next command.
N
OTE
:
ALE can be tied “High” if this signal is not available.
The Intel Read and Write timing diagram is shown in
Figure 36
. The timing specifications are shown in
Table 18
.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SH38_0609 | 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SH38IB | 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL216 | 16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL216_06 | 16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL216IB | 16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SH38_0609 | 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SH38ES | 功能描述:外圍驅動器與原件 - PCI 8 CHT1/E1LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SH38IB | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SH38IB-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL216 | 制造商:EXAR 制造商全稱:EXAR 功能描述:16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。