參數資料
型號: XRT83L38IB-F
廠商: Exar Corporation
文件頁數: 15/87頁
文件大?。?/td> 0K
描述: IC LIU T1/E1/J1 OCTAL 225BGA
標準包裝: 84
類型: 線路接口裝置(LIU)
驅動器/接收器數: 8/8
規程: T1,E1,J1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 225-BGA
供應商設備封裝: 225-BGA(19x19)
包裝: 托盤
XRT83L38
19
OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.2
POWER AND GROUND
TERSEL1
TERSEL0
T11
R11
I
Termination Impedance Select bit 1:
Termination Impedance Select bit 0:
In the
Hardware mode and in the internal termination mode (TXTSEL=”1” and RXT-
SEL=”1”) TERSEL[1:0] control the transmit and receive termination impedance
according to the following table.
In the
internal termination mode the receiver termination of each receiver is realized
completely by internal resistors or by the combination of internal and one fixed external
resistor (see description of RXRES[1:0] pins).
In the
internal termination mode the transformer ratio of 1:2 or 1:2.45 and 1:1 is
required for transmitter and receiver respectively with the transmitter output AC cou-
pled to the transformer.
NOTES:
1.
This pin is internally pulled “Low” with a 50k
Ω resistor.
2.
In Hardware mode, all channels share the same TERSEL control function.
3.
In the external termination mode a 1:2 or 1:2.45 transformer ratio must be
used for the transmitter.
TEST
U12
I
Manufacturing Test:
NOTE: For normal operation this pin must be tied to ground.
ICT
V12
I
In-Circuit Testing (Active “Low”):
When this pin is tied “Low”, all output pins are forced to a high impedance state for in-
circuit testing.
Pulling RESET and ICT pins “Low” simultaneously will put the chip in factory test
mode. This condition should not be permitted during normal operation.
NOTE: This pin is internally pulled “High” with a 50k
Ω resistor.
SIGNAL NAME
LEAD #
TYPE
DESCRIPTION
TGND_0
TGND_1
TGND_2
TGND_3
TGND_4
TGND_5
TGND_6
TGND_7
D3
F2
E15
C17
R3
P3
T16
R16
****
Transmitter Analog Ground for Channel _0
Transmitter Analog Ground for Channel _1
Transmitter Analog Ground for Channel _2
Transmitter Analog Ground for Channel _3
Transmitter Analog Ground for Channel _4
Transmitter Analog Ground for Channel _5
Transmitter Analog Ground for Channel _6
Transmitter Analog Ground for Channel _7
SIGNAL NAME
LEAD #TYPE
DESCRIPTION
0
1
0
1
0
100
Ω
110
Ω
75
Ω
120
Ω
Termination
TERSEL1
TERSEL0
相關PDF資料
PDF描述
XRT83SH314IB-F IC LIU T1/E1/J1 14CH 304TBGA
XRT83SH38IB-F IC LIU SH T1/E1/J1 8CH 225BGA
XRT86L30IV-F IC LIU/FRAMER TI/E1/J1 SGL 128LQ
XRT86VL30IV-F IC FRAMR/LIU T1/E1/J1 QD 128LQFP
XRT86VL32IB-F IC LIU/FRAMER T1/E1/J1 2CH 225BG
相關代理商/技術參數
參數描述
XRT83L38IV 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SH314 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SH314_0610 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SH314ES 功能描述:外圍驅動器與原件 - PCI 14 CHT1/E1LIU SH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83SH314IB 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray