參數資料
型號: XRT73L03BIV-F
廠商: Exar Corporation
文件頁數: 49/61頁
文件大?。?/td> 0K
描述: IC LIU E3/DS3/STS-1 3CH 120LQFP
標準包裝: 72
類型: 線路接口裝置(LIU)
驅動器/接收器數: 3/3
規程: DS3,E3,STS-1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 120-LQFP
供應商設備封裝: 120-LQFP(14x20)
包裝: 托盤
XRT73L03B
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.1
51
When the Transmit Drive Monitor circuitry within a
given line is connected to the line, as illustrated in
Figure 36, then it monitors the line for transitions. As
long as the Transmit Drive Monitor circuitry detects
transitions on the line via the MTIP_(n) and
MRing_(n) pins, then it keeps the DMO (Drive Moni-
tor Output) signal "Low". However, if the Transmit
Drive Monitor circuit detects no transitions on the line
for 128+32 TxClk periods, then the DMO (Drive Moni-
tor Output) signal toggles "High".
NOTE: The Transmit Drive Monitor circuit does not have to
be used to operate the Transmit Section of the XRT73L03B.
This is purely a diagnostic feature.
4.6
THE TAOS (TRANSMIT ALL ONES) FEATURE
The XRT73L03B can command any channel to trans-
mit an all “1’s" pattern onto the line by toggling a sin-
gle input pin or by setting a single bit-field within one
of the Command Registers to "1".
NOTE: When this feature is activated, the Transmit Section
of the configured channel overwrites the Terminal Equip-
ment data with this all “1’s" pattern.
a. Operating in the Hardware Mode
Configure Channel(n) to transmit an all “1’s" pattern
by toggling the TAOS_(n) input pin “High". Terminate
the all “1’s" pattern by toggling the TAOS_(n) input pin
“Low".
b. Operating in the HOST Mode
Configure Channel(n) to transmit an all “1’s" pattern
by writing to Command Register CR1-(n) and setting
the TAOS_(n) bit-field (bit D3) to "1".
Terminate the all “1’s" pattern by writing to Command
Register CR1-(n) and setting the TAOS_(n) bit-field
(D3) to "0".
5.0
THE MICROPROCESSOR SERIAL INTER-
FACE
The on-chip Command Registers of XRT73L03B
DS3/E3/STS-1 Line Interface Unit IC are used to con-
figure the XRT73L03B into a wide-variety of modes.
This section discusses the following:
1. The description of the Command Registers.
2. A description on how to use the Microprocessor
Serial Interface.
5.1
DESCRIPTION OF THE COMMAND REGISTERS
(repeated as Table 7), lists the Command Registers,
their Addresses and their bit-formats.
FIGURE 36. THE XRT73L03B EMPLOYING THE TRANSMIT DRIVE MONITOR FEATURES
R1 = 31.6
R2 = 31.6
Channel (n)
TxPOS_(n)
TxNEG_(n)
TxLineClk_(n)
TTIP_(n)
TRing_(n)
TPData_(n)
TNData_(n)
TxClk_(n)
Only One Channel Shown
1:1
J1
BNC
MTIP_(n)
MRing_(n)
R3 = 270
R4 = 270
COMMAND REGISTER CR1-(n)
D4
D3
D2
D1
D0
TxOFF_(n) TAOS_(n) TxClkINV_(n) TxLEV_(n) TxBIN_(n)
0
1X
X
相關PDF資料
PDF描述
XRT73L04BIV-F IC LIU E3/DS3/STS-1 4CH 144LQFP
XRT73L06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT73LC00AIV-F IC LIU STS1/DS3/E3 SGL 44TQFP
XRT73LC03AIV-F IC LIU E3/DS3/STS-1 3CH 120LQFP
XRT73LC04AIV-F IC LIU E3/DS3/STS-1 4CH 144LQFP
相關代理商/技術參數
參數描述
XRT73L03IV 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL E3/DS3/STS-1 LINE INTERFCE UNIT
XRT73L03IVS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
XRT73L04A 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73L04AIV 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73L04B 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT