- 您現在的位置：買賣IC網 > PDF目錄3766 > XR68M752IM48-F (Exar Corporation)IC UART FIFO 64B DUAL 48TQFP PDF資料下載
參數資料
| 型號： | XR68M752IM48-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 30/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 64B DUAL 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 1.62 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1479 1016-1479-ND 1016-1642 XR68M752IM48-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
XR16M752/XR68M752
36
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.1.1
4.10
Scratch Pad Register (SPR) - Read/Write
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle. There are also
two other registers (TLR and FIFO Rdy) that share the same address location as the Scratch Pad Register.
See Table 12.
4.11
Transmission Control Register (TCR) - Read/Write (requires EFR bit-4 = 1)
This register replaces MSR and is accessible only when MCR[6] = 1. This 8-bit register is used to store the RX
FIFO threshold levels to halt/resume transmission during hardware or software flow control.
TCR[3:0]: RX FIFO Halt Level
A value of 0-60 (decimal value of TCR[3:0] multiplied by 4) can be selected as the Halt Level. When the RX
FIFO is greater than or equal to this value, the RTS# output will be de-asserted if Auto RTS flow control is used
or the XOFF character(s) will be transmitted if Auto XON/XOFF flow control is used. It is recommended that
this value is greater than the RX Trigger Level.
TCR[7:4]: RX FIFO Resume Level
A value of 0-60 (decimal value of TCR[7:4] multiplied by 4) can be selected as the Resume Level. When the
RX FIFO is less than or equal to this value, the RTS# output will be re-asserted if Auto RTS flow control is used
or the XON character(s) will be transmitted if Auto XON/XOFF flow control is used. It is recommended that this
value is less than the RX Trigger Level.
4.12
Trigger Level Register (TLR) - Read/Write (requires EFR bit-4 = 1)
This register replaces SPR and is accessible under the conditions listed in Table 12. This 8-bit register is used
to store the RX and TX FIFO trigger levels used for interrupts.
TLR[3:0]: TX FIFO Trigger Level
A value of 4-60 (decimal value of TCR[3:0] multiplied by 4) can be selected as the TX FIFO Trigger Level.
When the number of available spaces in the TX FIFO is greater than or equal to this value, a Transmit Ready
interrupt is generated. For any non-zero value, TCR[3:0] will be used as the TX FIFO Trigger Level. If
TCR[3:0] = 0x0, then the TX FIFO Trigger Level is the value selected by FCR[5:4]. See Table 10.
TLR[7:4]: RX FIFO Trigger Level
A value of 4-60 (decimal value of TCR[7:4] multiplied by 4) can be selected as the RX FIFO Trigger Level.
When the number of characters received in the RX FIFO is greater than or equal to this value, a Receive Data
Ready interrupt is generated (a Receive Data Timeout interrupt is independent of the RX FIFO Trigger Level
and can be generated any time there is at least 1 byte in the RX FIFO and the RX input has been idle for the
timeout period described in “Section 2.10, Receiver” on page 17). For any non-zero value, TCR[7:4] will be
used as the RX FIFO Trigger Level. If TCR[7:4] = 0x0, then the RX FIFO Trigger Level is the value selected by
FCR[7:6]. See Table 10.
4.13
Baud Rate Generator Registers (DLL, DLM and DLD[3:0]) - Read/Write
These registers make-up the value of the baud rate divisor. The concatenation of the contents of DLM and
DLL is a 16-bit value is then added to DLD[3:0]/16 to achieve the fractional baud rate divisor. DLD must be
enabled via EFR bit-4 before it can be accessed. SEE ”PROGRAMMABLE BAUD RATE GENERATOR
DLD[5:4]: Sampling Rate Select
These bits select the data sampling rate. By default, the data sampling rate is 16X. The maximum data rate will
double if the 8X mode is selected and will quadruple if the 4X mode is selected. See Table 14 below.
TABLE 14: SAMPLING RATE SELECT
DLD[5]
DLD[4]
SAMPLING RATE
0
16X
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M752IM48-F | IC UART FIFO 34B DUAL 48TQFP |
| ST16C450CQ48-F | IC UART SINGLE 48TQFP |
| ST16C2450IQ48-F | IC UART FIFO DUAL 48TQFP |
| MAX7314AEG+T | IC I/O EXPANDER I2C 16B 24QSOP |
| ST16C550IQ48-F | IC UART FIFO 16B SGL 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR68M752IM48TR-F | 制造商:Exar Corporation 功能描述:XR68M752 Series 16 Mbps High Performance DUART With 64-Byte FIFO - TQFP-48 |
| XR7090AA-BC-0001 | 制造商:CREE 制造商全稱:Cree, Inc 功能描述:XLamp㈢ XR LED Binning and Labeling |
| XR7090AA-BC-DD-EF-G-HHHH | 制造商:CREE 制造商全稱:Cree, Inc 功能描述:XLamp㈢ XR LED Binning and Labeling |
| XR7090-AM-L1-0001 | 制造商:Cree 功能描述:LED AMBER XR 制造商:Cree 功能描述:LED, AMBER, XR 制造商:Cree 功能描述:LED, HIGH BRIGHTNESS, RED ORANGE, 67.2LM; Series:XLamp XR; LED Color:Amber; Luminous Flux @ Test:42lm; Wavelength Typ:595nm; Forward Current @ Test:350mA; Forward Current If Max:700mA; Forward Voltage @ Test:2.25V; Viewing Angle:100;RoHS Compliant: Yes |
| XR7090AM-L1-0001 | 制造商:Cree 功能描述:LED Uni-Color Amber 2-Pin SMD |
發布緊急采購，3分鐘左右您將得到回復。