- 您現在的位置：買賣IC網 > PDF目錄1976 > XR19L402IL48-F (Exar Corporation)IC UART/TXRX RS485 48QFN PDF資料下載
參數資料
| 型號： | XR19L402IL48-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 2/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART/TXRX RS485 48QFN |
| 標準包裝： | 260 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-QFN-EP（7x7） |
| 包裝： | 托盤 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
XR19L402
10
TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
REV. 1.0.3
voltage at the pin should be 3.3V when an external clock is supplied. For programming details, see
“Programmable Baud Rate Generator.”
FIGURE 5. TYPICAL CRYSTAL CONNECTIONS
C1
22-47pF
C2
22-47pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500K - 1M
XTAL1
XTAL2
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins. When VCC = 5V, the on-chip oscillator
can operate with a crystal whose frequency is not greater than 24 MHz. On the other hand, the L402 can
accept an external clock of up to 64 MHz at XTAL1 pin which results in a maximum data rate of 8 Mbps. For
further reading on the oscillator circuit please see DAN108 on EXAR’s web site at http://www.exar.com.
2.9
Programmable Baud Rate Generator with Fractional Divisor
Each UART has its own Baud Rate Generator (BRG) with a prescaler for the transmitter and receiver. The
prescaler is controlled by a software bit in the MCR register. The MCR register bit-7 sets the prescaler to divide
the input crystal or external clock by 1 or 4. The output of the prescaler clocks to the BRG. The BRG further
divides this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/16) to
obtain a 16X or 8X sampling clock of the serial data rate. The sampling clock is used by the transmitter for data
bit shifting and receiver for data sampling. The BRG divisor (DLL, DLM and DLD registers) defaults to the value
of ’1’ (DLL = 0x01, DLM = 0x00 and DLD = 0x00) upon reset. Therefore, the BRG must be programmed during
initialization to the operating data rate. The DLL and DLM registers provide the integer part of the divisor and
the DLD register provides the fractional part of the dvisior. Only the four lower bits of the DLD are implemented
and they are used to select a value from 0 (for setting 0000) to 0.9375 or 15/16 (for setting 1111). Programming
the Baud Rate Generator Registers DLL, DLM and DLD provides the capability for selecting the operating data
rate. Table 5 shows the standard data rates available with a 24MHz crystal or external clock at 16X clock rate.
If the pre-scaler is used (MCR bit-7 = 1), the output data rate will be 4 times less than that shown in Table 5. At
8X sampling rate, these data rates would double. Also, when using 8X sampling mode, please note that the bit-
time will have a jitter (+/- 1/16) whenever the DLD is non-zero and is an odd number. When using a non-
standard data rate crystal or external clock, the divisor value can be calculated with the following equation(s):
Required Divisor (decimal) = (XTAL1 clock frequency / prescaler) / (serial data rate x 16), with 16X mode EMSR[7] = 1
Required Divisor (decimal) = (XTAL1 clock frequency / prescaler / (serial data rate x 8), with 8X mode EMSR[7] = 0
相關PDF資料 |
PDF描述 |
|---|---|
| XR20M1170IL24TR-F | IC UART FIFO I2C/SPI 64B 24QFN |
| XR20M1172IG28-F | IC UART FIFO I2C/SPI 64B 28TSSOP |
| XR20M1280IL40-F | IC UART I2C/SPI 128 BYTE 40QFN |
| XR20V2170IL40-F | IC UART/TXRX I2C/SPI RS232 40QFN |
| XR20V2172IL64-F | IC UART/TXRX I2C/SPI RS232 64QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR1AEX2NV1XX | 制造商:Eaton Corporation 功能描述:SWITCH, ROCKER, SPST, 18A, 125VAC, BLACK, Contact Configuration:SPST, Switch Ope 制造商:Eaton Corporation 功能描述:SWITCH, ROCKER, SPST, 18A, 125VAC, BLACK, Contact Configuration:SPST, Switch Operation:Off-On, Contact Current Max:18A, Contact Voltage AC Nom:125V, Switch Mounting:Panel, Actuator / Cap Color:Red, Illumination Color:Red , RoHS Compliant: Yes |
| XR1AEX3NV1XX | 制造商:Eaton Corporation 功能描述:SWITCH, ROCKER, SPST, 18A, 125VAC, BLACK, Contact Configuration:SPST, Switch Ope |
| XR1AEX4NV1XX | 制造商:Eaton Corporation 功能描述:SWITCH, ROCKER, SPST, 18A, 125VAC, BLACK, Contact Configuration:SPST, Switch Operation:Off-On, Contact Current Max:18A, Contact Voltage AC Nom:125V, Switch Mounting:Panel, Actuator / Cap Color:Amber, Illumination Color:Amber , RoHS Compliant: Yes |
| XR1BG33NV1XX | 制造商:Eaton Corporation 功能描述:SWITCH, ROCKER, SPDT, 18A, 125VAC, BLACK, Contact Configuration:SPDT, Switch Ope |
| XR1BG44NV1XX | 制造商:Eaton Corporation 功能描述:SWITCH, ROCKER, SPDT, 18A, 125VAC, BLACK, Contact Configuration:SPDT, Switch Operation:On-Off-On, Contact Current Max:18A, Contact Voltage AC Nom:125V, Switch Mounting:Panel, Actuator / Cap Color:Amber, Illumination Color:Amber , RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。