- 您現在的位置：買賣IC網 > PDF目錄203625 > W29GL128CL1B (WINBOND ELECTRONICS CORP) 128M X 1 FLASH 3V PROM, 100 ns, PBGA64 PDF資料下載
參數資料
| 型號： | W29GL128CL1B |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 128M X 1 FLASH 3V PROM, 100 ns, PBGA64 |
| 封裝： | 11 X 13 MM, GREEN, BGA-64 |
| 文件頁數： | 7/63頁 |
| 文件大?。?/td> | 552K |
| 代理商： | W29GL128CL1B |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
W29GL128C
Publication Release Date: July 28, 2010
9
Preliminary - Revision A
7.2.9.2
Chip Erase
The Chip Erase operation returns all memory locations containing a bit state of “0” to the “1” state,
effectively clearing all data. This action requires six instruction cycles to commence the erase
operation. The unlock sequence is the first two cycles, followed by the configuration cycle, the fourth
and fifth are also ”unlock cycles”, and the sixth cycle initiates the chip erase operation.
Once the chip erase algorithm begins, no other instruction will be accepted. However, if a hardware
reset is executed or the operating voltage is below acceptable levels, the chip erase operation will be
terminated and automatically returns to Read mode.
The embedded chip erase algorithm status can be verified by the following:
Status
DQ7
DQ6
DQ5
DQ2
RY/#BY
1
In progress
0
Toggling
0
Toggling
0
Exceeded time limit
0
Toggling
1
Toggling
0
Table 7-5
Polling During Embedded Chip Erase Operation
Note:
1.
RY/#BY is open drain pin and should be connected to VCC through a high value pull-up resistor.
7.2.10 Erase Suspend/Resume
If there is a sector erase operation in progress, an Erase Suspend instruction is the only valid
instruction that may be issued. Once the Erase Suspend instruction is executed during the 50s time-
out period following a Sector Erase instruction, the time-out period will terminate right away and the
device will enter Erase-Suspend Read mode. If an Erase Suspend instruction is executed after the
sector erase operation has started, the device will not enter Erase-Suspended Read mode until
approximately 20s (5s typical) time has elapsed. To determine the device has entered the Erase-
Suspend Read mode, use DQ6, DQ7 and RY/#BY status to verify the state of the device.
Once the device has entered Erase-Suspended Read mode, it is possible to read or program any
sector(s) except those being erased by the erase operation. Only the contents of the status register is
present when attempting to read a sector that has been scheduled to erase or be programmed when
in the suspend mode. A resume instruction must be executed and recommend checking DQ6 toggle
bit status, before issuing another erase instruction.
The status register bits can be verified to determine the current status of the device:
Status
DQ7
DQ6
DQ5 DQ3 DQ2 DQ1RY/#BY
Erase suspend read in erase suspended sector
1 No toggle 0 N/A Toggle N/A
1
Erase suspend read in non-erase suspended sector
Data
DataData Data Data
1
Erase suspend program in non-erase suspended sector DQ7# Toggle
0 N/A N/A N/A
0
Table 7-6
Polling During Embedded Erase Suspend
Instruction sets such as read silicon ID, sector protect verify, program, CFI query and erase resume
can also be executed during Erase-Suspend mode, except sector and chip erase.
7.2.11 Sector Erase Resume
Only in the Erase-Suspended Read mode can the Sector Erase Resume instruction be a valid
command. Once erase resumes, another Erase Suspend instruction can be executed, but allow a
400s interval between Erase Resume and the next Erase Suspend instruction.
相關PDF資料 |
PDF描述 |
|---|---|
| W29N102CP-55B | 64K X 16 FLASH 3.3V PROM, 55 ns, PQCC44 |
| W2D15A250A | 1 FUNCTIONS, 50 V, FERRITE CHIP |
| W1D15A270A | 1 FUNCTIONS, 50 V, FERRITE CHIP |
| W2Z1M72SJ38BC | 1M X 72 MULTI DEVICE SRAM MODULE, 3.8 ns, PBGA209 |
| W2Z512K72SJ35ES | 512K X 72 MULTI DEVICE SRAM MODULE, 3.5 ns, PBGA209 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W29GL128CL9B | 功能描述:IC FLASH 128MBIT 90NS 64LFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6 |
| W29GL128CL9B TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 64LFBGA |
| W29GL128CL9T | 功能描述:IC FLASH 128MBIT 90NS 56TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| W29GL128CL9T TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 56TSOP |
| W29NK50ZD | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:N-CHANNEL 500 V - 0.11? - 29A TO-247 Fast Diode SuperMESH? MOSFET |
發布緊急采購，3分鐘左右您將得到回復。