參數資料
型號： W19B322MTB9G
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 2M X 16 FLASH 3V PROM, 90 ns, PBGA48
封裝： TFBGA-48
文件頁數： 3/52頁
文件大小： 1955K
代理商： W19B322MTB9G
W19B32XMT/B
Publication Release Date: March 23, 2004
- 11 -
Revision A2
The addresses will be latched on the falling edge of #WE or #CE, whichever happens later; while the
data will be latched on the rising edge of #WE or #CE, whichever happens first. Please refer to timing
waveforms.
6.2.1 Reading Array Data
After device power-up, it is automatically set to reading array data. There is no commands are
required to retrieve data. After completing an Embedded Program or Embedded Erase algorithm,
each bank is ready to read array data.
After the device accepts an Erase Suspend command, the corresponding bank enters the erase-
suspend-read mode. After it the system can read data from any non-erase-suspended sector within
the same bank. And then, after completing a programming operation in the Erase Suspend mode, the
system may once again read array data with the same exception. Please refer to Erase
Suspend/Erase Resume Commands section for detail information.
The system must initiate the reset command to return a bank to read (or erase-suspend-read) mode if
DQ5 goes high during an active program or erase operation, or the bank is in the autoselect mode.
See Reset Command section and Requirements for Reading Array Data in the Device Bus Operations
section for more information.
6.2.2 Reset Command
The banks will be to the read or erase-suspend-read mode when writing the reset command. For this
command, the address bits are Don’t Care.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the bank to which the system was writing to the read mode. Once
erasure begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command sequence
before programming begins. This resets the bank, to which the system was writing to the read mode.
If the program command sequence is written to a bank, in the Erase Suspend mode, writing the reset
command returns that bank to the erase-suspend-read mode. When programming begins, the device
ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command
sequence. When in the autoselect mode, the reset command must be written to return to the read
mode. If a bank entered into the autoselect mode while in the Erase Suspend mode, writing the reset
command returns that bank to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the banks to
the read mode (or erase-suspend-read mode if that bank was in Erase Suspend).
6.2.3 Autoselect Command Sequence
The autoselect command sequence provides the host system to access the manufacturer and device
codes, and determine whether a sector is protected or not. This is an alternative method, which is
intended for PROM programmers and requires VID on address pin A9. The autoselect command
sequence may be written to an address within a bank that is either in the read or erase-suspend-read
mode. When the device is actively programming or erasing in the other bank, the autoselect command
may not be written.
相關PDF資料
PDF描述
WV3EG265M72EFSU335D4ING 128M X 72 DDR DRAM MODULE, 0.7 ns, ZMA200
W3DG7216V10D2 8M X 72 SYNCHRONOUS DRAM MODULE, DMA168
W7NCF01GH10CSAAEM1G FLASH 3.3V PROM MODULE, XMA50
W7NCF01GH10IS4FM1G FLASH 3.3V PROM MODULE, XMA50
W7NCF01GH10IS9FM1G FLASH 3.3V PROM MODULE, XMA50
相關代理商/技術參數
參數描述
W19L-E02050 制造商:Cooper Crouse-Hinds 功能描述:
W19L-E03040 制造商:Cooper Crouse-Hinds 功能描述:
W19L-E04040 制造商:Cooper Crouse-Hinds 功能描述:
W19U_5LGA WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
W1A 功能描述:ENCLOSURE 7.25X4.5 GREY RoHS:是 類別:盒，外殼，支架 >> 箱 系列:工具 產品目錄繪圖:SR Series Standard 特色產品:Customize Your Enclosure 標準包裝:1 系列:S 容器 - 類型:盒 尺寸/尺寸:3.600" L x 2.250" W（91.44mm x 57.15mm） 高度:1.500"（38.10mm） 面積 (L x W):8.10"（52.3cm） 設計:手持，分叉式雙側 材質:塑料 - ABS 顏色:杏黃 厚度:0.100"（2.54mm） 特點:PCB 支座 額定值:IP40，NEMA 1 材料可燃性額定值:UL94 HB 裝運信息:從 Digi-Key 運送 重量:0.137 磅（62.14g） 相關產品:SR6005-ND - SCREW NO.4X 3/8 H/L PANSRPS-11-ND - GASKET 3.63 X 2.27 INCHSR52-ND - BOX RUBBER FEET FOR "A" SERIESSR410-ND - PC BOARD COPPER CLADSR310-ND - PC BOARD .1" STD HORIZ GRIDSR50-ND - RUBBER FEET (1XX,2XX) 其它名稱:111-I ALMOND111-IA111-IALMONDSR111-IA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*