- 您現在的位置：買賣IC網 > PDF目錄245678 > W19B320ATT9G (WINBOND ELECTRONICS CORP) 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 PDF資料下載
參數資料
| 型號： | W19B320ATT9G |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| 封裝： | 12 X 20 MM, TSOP-48 |
| 文件頁數： | 10/53頁 |
| 文件大小： | 479K |
| 代理商： | W19B320ATT9G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
W19B320AT/B
- 18 -
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit.
DQ5 produces “1” under these conditions which indicates that the program or erase cycle was not
successfully completed.
The device may output “1” on DQ5 if the system tries to program “1” to a location that was previously
programmed to “0.” Only the erase operation can change “0” back to “1.” Under this condition, the device
stops the operation, and while the timing limit has been exceeded, DQ5 produces “1.”
Under both these conditions, the system must write the reset command to return to the read mode (or to the
erase-suspend-read mode if a bank was previously in the erase-suspend-program mode).
6.3.7
DQ3: Sector Erase Timer
After writing a sector erasure command sequence, the system may read DQ3 to determine whether erasure
has begun or not. (The sector erase timer does not apply to the chip erase command.) The entire time-out
applies after each additional sector erasure command if additional sectors are selected for erasure. Once
the timeout period has completed, DQ3 switches from “0” to “1.” If the time between additional sector erase
commands from the system can be assumed to be less than 50
μs, the system need not monitor, DQ3 does
not need to be monitored. Please also refer to Sector Erase Command Sequence section.
After the sector erase command is written, the system should read the status of DQ7 (
#Data Polling) or
DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If
DQ3 is“1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are
ignored until the erase operation is complete. If DQ3 is “0,” the device will accept additional sector erase
commands.
The system software should check the status of DQ3 before and following each subsequent sector erase
command to ensure the command has been accepted. If DQ3 is high on the second status check, the last
command might not have been accepted.
相關PDF資料 |
PDF描述 |
|---|---|
| WE128K32-200HSC | 512K X 8 EEPROM 5V MODULE, 200 ns, CHIP66 |
| WS512K32-20G4M | 2M X 8 MULTI DEVICE SRAM MODULE, 20 ns, CQFP68 |
| WS512K32-55G4I | 2M X 8 MULTI DEVICE SRAM MODULE, 55 ns, CQFP68 |
| WPDE8M72V-70MDCT | 8M X 72 EDO DRAM MODULE, 70 ns, PDMA168 |
| WE512K8-150CIA | 512K X 8 EEPROM 5V MODULE, 150 ns, CDIP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W19B320B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
| W19B320BB | 制造商:WINBOND 制造商全稱:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
| W19B320BB-H | 制造商:WINBOND 制造商全稱:Winbond 功能描述:2.7~3.6-volt write (program and erase) operations |
| W19B320BB-M | 制造商:WINBOND 制造商全稱:Winbond 功能描述:2.7~3.6-volt write (program and erase) operations |
| W19B320BT | 制造商:WINBOND 制造商全稱:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
發布緊急采購，3分鐘左右您將得到回復。