參數資料
型號: TPA5051_07
廠商: Texas Instruments, Inc.
英文描述: FOUR CHANNEL DIGITAL AUDIO LIP-SYNC DELAY WITH I2C CONTROL
中文描述: 四通道數字音頻口形同步延遲與I2C控制
文件頁數: 7/21頁
文件大?。?/td> 710K
代理商: TPA5051_07
www.ti.com
GENERAL I
2
C OPERATION
The I
2
C bus employs two signals; SDA (data) and SCL (clock), to communicate between integrated circuits in a
system. Data is transferred on the bus serially, one bit at a time. The address and data are transferred in byte
(8-bit) format with the most-significant bit (MSB) transferred first. In addition, each byte transferred on the bus is
acknowledged by the receiving device with an acknowledge bit. Each transfer operation begins with the master
device driving a start condition on the bus and ends with the master device driving a stop condition on the bus.
The bus uses transitions on the data terminal (SDA) while the clock is high to indicate start and stop conditions.
A high-to-low transition on SDA indicates a start and a low-to-high transition indicates a stop. Normal data-bit
transitions must occur within the low time of the clock period. These conditions are shown in
Figure 5
. The
master generates the 7-bit slave address and the read/write (R/W) bit to open communication with another
device and then wait for an acknowledge condition. The TPA5051 holds SDA low during acknowledge clock
period to indicate an acknowledgement. When this occurs, the master transmits the next byte of the sequence.
Each device is addressed by a unique 7-bit slave address plus R/W bit (1 byte). All compatible devices share
the same signals via a bidirectional bus using a wired-AND connection.
Register (N)
8- Bit Data for
8- Bit Data for
Register (N+1)
SINGLE-AND MULTIPLE-BYTE TRANSFERS
The serial control interface supports both single-byte and multi-byte read/write operations for all registers.
TPA5051
SLOS497A–JUNE 2006–REVISED JULY 2006
APPLICATION INFORMATION (continued)
An external pull-up resistor must be used for the SDA and SCL signals to set the HIGH level for the bus. When
the bus level is 5 V, pull-up resistors between 1 k
and 2 k
in value must be used. For a bus level of 3.3 V,
higher resistor values, such as 10 k
, may be used.
Figure 5. Typical I
2
C Sequence
There is no limit on the number of bytes that can be transmitted between start and stop conditions. When the
last word transfers, the master generates a stop condition to release the bus. A generic data transfer sequence
is shown in
Figure 5
.
The 7-bit address for the TPA5051 is selectable using the 3 address pins (ADD0, ADD1, ADD2).
Table 1
lists
the 8 possible slave addresses.
Table 1. I
2
C Slave Address
SELECTABLE ADDRESS BITS
ADD1
0
0
1
1
0
0
1
1
FIXED ADDRESS
(4 MSB bits)
ADD2
0
0
0
0
1
1
1
1
ADD0
0
1
0
1
0
1
0
1
1101
1101
1101
1101
1101
1101
1101
1101
During multiple-byte read operations, the TPA5051 responds with data, a byte at a time, starting at the register
assigned, as long as the master device continues to respond with acknowledges.
7
Submit Documentation Feedback
相關PDF資料
PDF描述
TPIC2701M 7-CHANNEL COMMON-SOURCE POWER DMOS ARRAY
TPIC2701MJ 7-CHANNEL COMMON-SOURCE POWER DMOS ARRAY
TPIC43T01 Three-Phase Brushless Motor RPM Controller
TPIC43T01DA THREE-PHASE BRUSHLESS MOTOR RPM CONTROLLERS
TPS2010(中文) Power Distribution Switch(過流、限流、欠壓鎖定、熱關閉及ESD保護,電源分配開關)
相關代理商/技術參數
參數描述
TPA5051EVM 功能描述:音頻 IC 開發工具 AUD DELAY DEVICE RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA5051RSAR 功能描述:音頻 DSP 4Ch Dig Aud Delay Proc RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
TPA5051RSARG4 功能描述:音頻 DSP 4Ch Dig Aud Delay Proc RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
TPA5051RSAT 功能描述:音頻 DSP 4Ch Dig Aud Delay Proc RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
TPA5051RSATG4 功能描述:音頻 DSP 4Ch Dig Aud Delay Proc RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube