- 您現在的位置：買賣IC網 > PDF目錄385007 > TP11362AN (NATIONAL SEMICONDUCTOR CORP) CONNECTOR ACCESSORY PDF資料下載
參數資料
| 型號： | TP11362AN |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 編解碼器 |
| 英文描述： | CONNECTOR ACCESSORY |
| 中文描述： | A/MU-LAW, ADPCM CODEC, PDIP24 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-24 |
| 文件頁數： | 4/16頁 |
| 文件大小： | 442K |
| 代理商： | TP11362AN |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Functional Description
(Continued)
The TP11362A is capable of processing eight independent
channels (half duplex) or four full-duplex PCM channels
within 125 μs (8 kHz).
The logic state of TRB at the falling edge of CE determines
which input register is active during that CE period and which
output register will be active in the following third CE period.
The input data is processed (PCM data encoded or ADPCM
data decoded) during the second cycle and shifted out in the
third cycle of CE while CE is high.
SERIAL I/O
Input data is transferred into the TP11362A on the falling
edge of the clock signal, while output data is transmitted on
the rising edge of the clock signal. PCM data is transferred
synchronously using PSCK, while ADPCM data is trans-
ferred synchronously using ASCK. The clock signals ASCK
and PSCK should be high while CE changes. All serial data
is transferred with MSB first. Figure 2 and Figure 3 show the
serial input and output structures, respectively.
PCM Serial Input Register
The serial PCM data to be encoded is shifted into the 8-bit
PCM input register with the falling edges of PSCK while CE
and TRB are high. The falling edge of CE latches the state of
the input register and transfers the last 8 bits data prior to the
CE transition to the core for processing. The 8-bit PCM input
register is cleared asynchronously with RSTB going low.
ADPCM Serial Input Register
The ADPCM serial input register is a 5-bit shift register to
store the 5-bit data in the 40 kbpsADPCM mode. Serial input
data is latched in with the falling edges of ASCK while CE is
high and TRB is low. A minimum number of five low going
ASCK pulses must be available within the CE pulse when
operating in the 40 kbps mode. For the 32, 24 and 16 kbps
modes,ASCK must be pulsed low 4 times while CE is high to
read in the RSI data. The falling edge of CE latches the last
5 bits data in the 40 kbps mode or the last 4 bits data in the
32, 24, and 16 kbps modes prior to the CE transistion. See
Table 3 for the position of the ADPCM data in the 5-bit input
register when 5 ASCK low going pulses occur while CE is
high and TRB is low. Bit 1 in Table 3 is the LSB which is the
last bit in 32 and 40 kbps modes referenced to the negative
edge of CE.
ADPCM Output Register
The internal encoded parallel ADPCM data is loaded into the
5-bit ADPCM output register with the falling edge of CE sig-
nal. The first MSB data is shifted out after the rising edge of
CE, subsequent ADPCM serial data is shifted out with the
rising edge of ASCK. Table 4 shows the transfer order of the
ADPCM output data. If more than 4 ASCK clocks are avail-
able while CE is high in the 32, 24, and 16 kbps modes, the
ADPCM output data will recirculate starting with the MSB. In
the case of the 40 kbps mode, theADPCM output pattern will
recirculate, starting with the MSB, with the fifth rising edge of
ASCK while CE is high.
PCM Output Register
The decoded 8-bit parallel PCM data is loaded into an 8-bit
parallel-to-serial output shift register with the falling edge of
CE. The MSB data is shifted out with the leading edge of CE,
and subsequent data are shifted out with the rising edges of
PSCK while CE is high. The 8-bit PCM data at the RSO out-
put will recirculate with the MSB first after the seventh rising
edge of PSCK while CE is high.
Figure 4shows the full duplex timing diagram for the 40 kbps
mode. For the 32, 24 and 16 kbps modes only fourASCK low
pulses are needed while CE is high.
TRB is alternate high and low in the full duplex mode at each
falling edge of CE for a transmit (encoder) operation followed
DS012877-4
FIGURE 2. Serial Input Structure
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| TP11368 | Octal Adaptive Differential PCM Processor |
| TP11368N | Octal Adaptive Differential PCM Processor |
| TP11368V | Octal Adaptive Differential PCM Processor |
| TP1251 | ILLUMINATED PUSHBUTTON SWITCHES |
| TP1251G | ILLUMINATED PUSHBUTTON SWITCHES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TP11362AV | 制造商:Texas Instruments 功能描述: |
| TP11362AV/NOPB | 功能描述:IC PROCESSOR QUAD DIF PCM 28PLCC RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| TP11368 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Octal Adaptive Differential PCM Processor |
| TP11368N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Octal Adaptive Differential PCM Processor |
| TP11368V | 功能描述:編碼器、解碼器、復用器和解復用器 RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。