- 您現在的位置：買賣IC網 > PDF目錄17097 > TOOLSTICK300DC (Silicon Laboratories Inc)TOOLSTICK DAUGHTER CARD PDF資料下載
參數資料
| 型號： | TOOLSTICK300DC |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 9/178頁 |
| 文件大?。?/td> | 0K |
| 描述： | TOOLSTICK DAUGHTER CARD |
| 標準包裝： | 1 |
| 系列： | ToolStick |
| 類型： | MCU |
| 適用于相關產品： | C8051F300 |
| 所含物品： | 子卡 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁
C8051F300/1/2/3/4/5
106
Rev. 2.9
12.2. Port I/O Initialization
Port I/O initialization consists of the following steps:
Step 1. Select the input mode (analog or digital) for all Port pins, using the Port0 Input Mode
register (P0MDIN).
Step 2. Select the output mode (open-drain or push-pull) for all Port pins, using the Port0 Output
Mode register (P0MDOUT).
Step 3. Set XBR0 to skip any pins selected as analog inputs or special functions.
Step 4. Assign Port pins to desired peripherals.
Step 5. Enable the Crossbar.
All Port pins must be configured as either analog or digital inputs. Any pins to be used as Comparator or
ADC inputs should be configured as an analog inputs. When a pin is configured as an analog input, its
weak pull-up, digital driver, and digital receiver is disabled. This process saves power and reduces noise
on the analog input. Pins configured as digital inputs may still be used by analog peripherals; however this
practice is not recommended.
Additionally, all analog input pins should be configured to be skipped by the Crossbar (accomplished by
setting the associated bits in XBR0). Port input mode is set in the P0MDIN register, where a ‘1’ indicates a
digital input, and a ‘0’ indicates an analog input. All pins default to digital inputs on reset. See SFR Defini-
tion 12.5 for the P0MDIN register details.
The output driver characteristics of the I/O pins are defined using the Port0 Output Mode register
P0MDOUT (see SFR Definition 12.6). Each Port Output driver can be configured as either open drain or
push-pull. This selection is required even for the digital resources selected in the XBRn registers, and is
not automatic. The only exception to this is the SMBus (SDA, SCL) pins, which are configured as open-
drain regardless of the P0MDOUT settings. When the WEAKPUD bit in XBR2 is ‘0’, a weak pull-up is
enabled for all Port I/O configured as open-drain. WEAKPUD does not affect the push-pull Port I/O. Fur-
thermore, the weak pull-up is turned off on an open-drain output that is driving a ‘0’ to avoid unnecessary
power dissipation.
Registers XBR0, XBR1 and XBR2 must be loaded with the appropriate values to select the digital I/O func-
tions required by the design. Setting the XBARE bit in XBR2 to ‘1’ enables the Crossbar. Until the Crossbar
is enabled, the external pins remain as standard digital inputs (output drivers disabled) regardless of the
XBRn Register settings. For given XBRn Register settings, one can determine the I/O pin-out using the
Priority Decode Table; as an alternative, the Configuration Wizard utility of the Silicon Labs IDE software
will determine the Port I/O pin assignments based on the XBRn Register settings.
相關PDF資料 |
PDF描述 |
|---|---|
| TOOLSTICK411DC | TOOLSTICK DAUGHTER CARD |
| TOOLSTICK336DC | DAUGHTER CARD TOOLSTICK C8051F33 |
| SDR-2 | SCOTCH CODE REFILL # 2 |
| 0210490198 | CABLE JUMPER 1.25MM .127M 14POS |
| RSM08DRTH | CONN EDGECARD 16POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TOOLSTICK300PP | 功能描述:插座和適配器 Dev Tool for C8051F30X MCUs RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
| TOOLSTICK300SPP | 功能描述:插座和適配器 TS for F300-F305 SOIC 14 MCUs RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
| TOOLSTICK310PP | 功能描述:插座和適配器 C8051F310/12/14 F361 F364 F366 F368 RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
| TOOLSTICK311DC | 功能描述:子卡和OEM板 ToolStick C8051F311 Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| TOOLSTICK311PP | 功能描述:插座和適配器 C8051F311/13/15 F362 F365 F367 F369 RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
發布緊急采購，3分鐘左右您將得到回復。