參數(shù)資料
型號: TOOLSTICK300DC
廠商: Silicon Laboratories Inc
文件頁數(shù): 16/178頁
文件大?。?/td> 0K
描述: TOOLSTICK DAUGHTER CARD
標準包裝: 1
系列: ToolStick
類型: MCU
適用于相關產品: C8051F300
所含物品: 子卡
C8051F300/1/2/3/4/5
112
Rev. 2.9
13.1. Supporting Documents
It is assumed the reader is familiar with or has access to the following supporting documents:
1.
The I2C-Bus and How to Use It (including specifications), Philips Semiconductor.
2.
The I2C-Bus Specification – Version 2.0, Philips Semiconductor.
3.
System Management Bus Specification – Version 1.1, SBS Implementers Forum.
13.2. SMBus Configuration
Figure 13.2 shows a typical SMBus configuration. The SMBus specification allows any recessive voltage
between 3.0 and 5.0 V; different devices on the bus may operate at different voltage levels. The bidirec-
tional SCL (serial clock) and SDA (serial data) lines must be connected to a positive power supply voltage
through a pull-up resistor or similar circuit. Every device connected to the bus must have an open-drain or
open-collector output for both the SCL and SDA lines, so that both are pulled high (recessive state) when
the bus is free. The maximum number of devices on the bus is limited only by the requirement that the rise
and fall times on the bus not exceed 300 ns and 1000 ns, respectively.
VDD = 5V
Master
Device
Slave
Device 1
Slave
Device 2
VDD = 3V
VDD = 5V
VDD = 3V
SDA
SCL
Figure 13.2. Typical SMBus Configuration
13.3. SMBus Operation
Two types of data transfers are possible: data transfers from a master transmitter to an addressed slave
receiver (WRITE), and data transfers from an addressed slave transmitter to a master receiver (READ).
The master device initiates both types of data transfers and provides the serial clock pulses on SCL. The
SMBus interface may operate as a master or a slave, and multiple master devices on the same bus are
supported. If two or more masters attempt to initiate a data transfer simultaneously, an arbitration scheme
is employed with a single master always winning the arbitration. Note that it is not necessary to specify one
device as the Master in a system; any device that transmits a START and a slave address becomes the
master for the duration of that transfer.
A typical SMBus transaction consists of a START condition followed by an address byte (Bits7–1: 7-bit
slave address; Bit0: R/W direction bit), one or more bytes of data, and a STOP condition. Each byte that is
received (by a master or slave) must be acknowledged (ACK) with a low SDA during a high SCL (see
Figure 13.3). If the receiving device does not ACK, the transmitting device will read a NACK (not acknowl-
edge), which is a high SDA during a high SCL.
相關PDF資料
PDF描述
TOOLSTICK411DC TOOLSTICK DAUGHTER CARD
TOOLSTICK336DC DAUGHTER CARD TOOLSTICK C8051F33
SDR-2 SCOTCH CODE REFILL # 2
0210490198 CABLE JUMPER 1.25MM .127M 14POS
RSM08DRTH CONN EDGECARD 16POS DIP .156 SLD
相關代理商/技術參數(shù)
參數(shù)描述
TOOLSTICK300PP 功能描述:插座和適配器 Dev Tool for C8051F30X MCUs RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x
TOOLSTICK300SPP 功能描述:插座和適配器 TS for F300-F305 SOIC 14 MCUs RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x
TOOLSTICK310PP 功能描述:插座和適配器 C8051F310/12/14 F361 F364 F366 F368 RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x
TOOLSTICK311DC 功能描述:子卡和OEM板 ToolStick C8051F311 Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
TOOLSTICK311PP 功能描述:插座和適配器 C8051F311/13/15 F362 F365 F367 F369 RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x