
www.ti.com
SLAS666 – JANUARY 2010
Electrical Characteristics (continued)
At 25°C, AVDD = HPVDD = IOVDD = 3.3 V, SPLVDD, SPRVDD = 3.6 V, DVDD = 1.8 V, fS (audio) = 48 kHz, CODEC_CLKIN
= 256 × fS, PLL = Off, VOL/MICDET pin disabled (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
AUDIO DAC
DAC Headphone Output, AC-Coupled Load = 16
(Single-Ended),
Driver Gain = 0 dB, Parasitic Capacitance = 30 pF
Full-scale output voltage (0
Output common-mode setting = 1.65 V
0.707
Vrms
dB)
SNR
Signal-to-noise ratio
Measured as idle-channel noise, A-weighted(1) (2)
80
95
dB
THD
Total harmonic distortion
0-dBFS input
–85
–65
dB
Total harmonic distortion +
THD+N
0-dBFS input
–82
–60
dB
noise
Mute attenuation
87
dB
PSRR
Power-supply rejection ratio(3)
Ripple on HPVDD (3.3 V) = 200 mVp-p at 1 kHz
–62
dB
RL = 32 , THD+N ≤ –60 dB
20
PO
Maximum output power
mW
RL = 16 , THD+N ≤ –60 dB
60
DAC Lineout (HP Driver in Lineout Mode)
SNR
Signal-to-noise ratio
Measured as idle-channel noise, A-weighted
95
dB
THD
Total harmonic distortion
0-dBFS input, 0-dB gain
–86
dB
Total harmonic distortion +
THD+N
0-dBFS input, 0-dB gain
–82
dB
noise
DAC Digital Interpolation Filter Characteristics
DAC Output to Class-D Speaker Output; Load = 8
(Differential), 50 pF
SPLVDD = SPRVDD = 3.6 V, BTL measurement,
CM = 1.8 V, DAC input = 0 dBFS,
2.2
class-D gain = 6 dB, THD
≤ –16.5 dB
Output voltage
Vrms
SPLVDD = SPRVDD = 3.6 V, BTL measurement,
CM = 1.8 V, DAC input = –2 dBFS,
2.1
class-D gain = 6 dB, THD
≤ –20 dB
SPLVDD = SPRVDD = 3.6 V, BTL measurement,
Output, common-mode
1.8
V
DAC input = mute, CM = 1.8 V, class-D gain = 6 dB
SPLVDD = SPRVDD = 3.6 V, BTL measurement,
class-D gain = 6 dB, measured as idle-channel noise,
SNR
Signal-to-noise ratio
87
dB
A-weighted (with respect to full-scale output value of
2.2 Vrms)(1) (2)
SPLVDD = SPRVDD = 3.6 V, BTL measurement,
THD
Total harmonic distortion
–67
dB
CM = 1.8 V, class-D gain = 6 dB
Total harmonic distortion +
SPLVDD = SPRVDD = 3.6 V, BTL measurement,
THD+N
–66
dB
noise
CM = 1.8 V, class-D gain = 6 dB
SPLVDD = SPRVDD = 3.6 V, BTL measurement,
PSRR
Power-supply rejection ratio(4)
–44
dB
ripple on SPLVDD/SPRVDD = 200 mVp-p at 1 kHz
Mute attenuation
110
dB
SPLVDD = SPRVDD = 3.6 V, BTL measurement,
540
CM = 1.8 V, class-D gain = 18 dB, THD = 10%
mW
SPLVDD = SPRVDD = 4.3 V, BTL measurement,
PO
Maximum output power
790
CM = 1.8 V, class-D gain = 18 dB, THD = 10%
SPLVDD = SPRVDD = 5.5 V, BTL measurement,
1.29
W
CM = 1.8 V, class-D gain = 18 dB, THD = 10%
(1)
Ratio of output level with 1-kHz full-scale sine-wave input, to the output level with the inputs short-circuited, measured A-weighted over a
20-Hz to 20-kHz bandwidth using an audio analyzer.
(2)
All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may
result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter
removes out-of-band noise, which, although not audible, may affect dynamic specification values.
(3)
DAC to headphone-out PSRR measurement is calculated as PSRR = 20 × log(
ΔVHPL / ΔVHPVDD).
(4)
DAC to speaker-out PSRR measurement is calculated as PSRR = 20 × log(
ΔVSPL(P + M) / ΔVSPLVDD).
Copyright 2010, Texas Instruments Incorporated
ELECTRICAL SPECIFICATIONS
7