參數資料
型號： TDA8505
廠商： NXP SEMICONDUCTORS
元件分類： 顏色信號轉換
英文描述： SECAM encoder
中文描述： COLOR SIGNAL ENCODER, PDIP32
封裝： PLASTIC, SOT-232-1, SDIP-32
文件頁數： 7/32頁
文件大小： 466K
代理商： TDA8505
July 1994
7
Philips Semiconductors
Preliminary specification
SECAM encoder
TDA8505
V
ERTICAL IDENTIFICATION
After the low frequency pre-emphasis the signal is
clamped and, if desired the vertical identification sawtooth
waveform can be added. The generation of the vertical
identification is switched on/off by the logic level input at
pin 26.
Figure 4 shows the sawtooth waveform at the input of the
FM modulator with the corresponding frequency values
after modulation.
Vertical identification is only possible if PLL tuning is
selected.
G
AIN
+
LIMITER
The gain of this amplifier is sequentially switched, so that
the amplitude of D'R is 280/230 times the amplitude of D'B
(based on an EBU colour bar). The signal is limited at a
lower and upper level to ensure that the FM modulator
frequencies are always between 3.9 MHz and 4.756 MHz.
A DC offset between D'R and D'B is added which
corresponds with the limiter levels.
FM
MODULATOR
The signal of the gain + limiter stage is fed to the FM
modulator.
The modulator control adjusts the DC level at pin 13 to set
the frequency of the FM signal to 4.406 MHz at the black
level of D'R. The modulator control also sets the DC level
at pin 15 to adjust the FM frequency to 4.250 MHz at the
black level of D'B.
At the start of every line the FM modulator is stopped and
is started again by a short duration pulse of the pulse
shaper. These stop/start pulses are operating such that
after two lines starting in the same phase, the start phase
of the third line is shifted 180 degrees. This sequence is
inverted during each vertical blanking.
The FM signal is fed to the internal HF pre-emphasis filter.
HF
PRE
-
EMPHASIS AND BANDPASS FILTER
An HF pre-emphasis filter combined with a bandpass filter
is integrated.
Figures 5 and 6 illustrate the frequency response. Two
resistors in series with a potentiometer at pin 14 adjusts
the frequency to 4.286 MHz with a tolerance of
±
20 kHz.
A tuning circuit integrated with an external capacitor
connected to pin 16 guarantees a stable frequency
response for the whole temperature range.
The output of the bandpass filter is connected directly to
the chrominance blanking circuit.
Fig.4 Vertical identification sawtooth waveform input.
handbook, full pagewidth
MLA954
64
μ
s
64
μ
s
3.90 MHz
35 kHz
4.250 MHz
4.406 MHz
4.756 MHz
35 kHz
frequency
after
modulation
D'R
D'B
18 s
6 s
μ
15 s
5 s
μ
相關PDF資料
PDF描述
TDA8510 26 W BTL and 2 x 13 W SE power amplifiers
TDA8510J 26 W BTL and 2 x 13 W SE power amplifiers
TDA8511 4 x 13 W single-ended power amplifiers
TDA8511J 4 x 13 W single-ended power amplifiers
TDA8541 1 W BTL audio amplifier
相關代理商/技術參數
參數描述
TDA8510 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:26 W BTL and 2 x 13 W SE power amplifiers
TDA8510J 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:26 W BTL and 2 x 13 W SE power amplifiers
TDA8510J/N2,112 功能描述:音頻放大器 AMP POWER 26W 17-SIL RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDA8511 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 x 13 W single-ended power amplifiers
TDA8511J 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 x 13 W single-ended power amplifiers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*