參數資料
型號： TDA8505
廠商： NXP SEMICONDUCTORS
元件分類： 顏色信號轉換
英文描述： SECAM encoder
中文描述： COLOR SIGNAL ENCODER, PDIP32
封裝： PLASTIC, SOT-232-1, SDIP-32
文件頁數： 10/32頁
文件大小： 466K
代理商： TDA8505
July 1994
10
Philips Semiconductors
Preliminary specification
SECAM encoder
TDA8505
Sync separator and pulse shaper
The composite sync input at pin 29 together with the
outputs of the 272 divider of the 4.250 MHz reference loop
are the sources for all pulses necessary for the processing.
The pulses are used for:
Clamping
Video blanking
FH/2
Chrominance blanking
Stop/start of modulator
Vertical identification
Timing for the modulator control
Sandcastle pulse shaping at pin 20.
External FH/2 at pin 4 is only necessary when two or more
SECAM encoders have to be locked in the same phase.
The phase of the internal FH/2 can be locked with an
external FH/2 connected at pin 4. A reset of the internal
FH/2 is possible by forcing pin 4 to a HIGH level. This
HIGH level corresponds with D'R. Pin 4 is connected to
ground when not used.
Figures 9 and 10 show the generated pulses during
vertical blanking for PLL tuning or crystal tuning
respectively. Figure 11 shows the pulses during line
blanking.
Transcoding application
A sandcastle pulse is necessary for the PAL/NTSC
demodulator (i.e. TDA4510) for transcoding PAL or NTSC
to SECAM.
Most of the demodulator ICs use a sandcastle pulse with
an amplitude of 12 V or 8 V. A 12 V or 8 V sandcastle is
not possible with the TDA8505 because of the 5 V power
supply.
To generate a 3-level sandcastle pulse at pin 20
(see Fig.8) an external supply voltage must be connected
to pin 19.
The PAL or NTSC CVBS signal is connected to the
composite sync input (pin 29) for PLL tuning and pulse
shaping. As previously mentioned the Y input at pin 5 can
be used as the Y+SYNC input for the filtered Y+SYNC PAL
or NTSC signal, when pin 12 is at a HIGH level.
Fig.8 3-level sandcastle pulse.
handbook, full pagewidth
MSA733 - 1
Vext
4.5 V 0.2 V
2.5 V 0.2 V
0.5 V
相關PDF資料
PDF描述
TDA8510 26 W BTL and 2 x 13 W SE power amplifiers
TDA8510J 26 W BTL and 2 x 13 W SE power amplifiers
TDA8511 4 x 13 W single-ended power amplifiers
TDA8511J 4 x 13 W single-ended power amplifiers
TDA8541 1 W BTL audio amplifier
相關代理商/技術參數
參數描述
TDA8510 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:26 W BTL and 2 x 13 W SE power amplifiers
TDA8510J 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:26 W BTL and 2 x 13 W SE power amplifiers
TDA8510J/N2,112 功能描述:音頻放大器 AMP POWER 26W 17-SIL RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDA8511 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 x 13 W single-ended power amplifiers
TDA8511J 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 x 13 W single-ended power amplifiers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*