參數資料
型號: ST62E35B
廠商: 意法半導體
英文描述: 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, 16-BIT AUTO-RELOAD TIMER, EEPROM, SPI AND UART
中文描述: 8位檢察官辦公室/存儲器與阿微控制器/ D轉換器,16位自動重加載定時器,EEPROM中,SPI和UART
文件頁數: 59/82頁
文件大小: 617K
代理商: ST62E35B
59/82
ST62T35B/E35B
4.6 SERIAL PERIPHERAL INTERFACE (SPI)
The on-chip SPI is an optimized serial synchro-
nous interface that supports a wide range of in-
dustry standard SPI specifications. The on-chip
SPI is controlled by small and simple user soft-
ware to perform serial data exchange. The serial
shift clock can be implemented either by software
(using the bit-set and bit-reset instructions), with
the on-chip Timer 1 by externally connecting the
SPI clock pin to the timer pin or by directly apply-
ing an external clock to the Scl line.
The peripheral is composed by an 8-bit Data/shift
Register and a 4-bit binary counter while the Sin
pin is the serial shift input and Sout is the serial
shift output. These two lines can be tied together
to implement two wires protocols
(I C-b
us, etc).
When data is serialized, the MSB is the first bit.
Sin has to be programmed as input. For serial out-
put operation Sout has to be programmed as
open-drain output.
The SCL, Sin and Sout SPI clock and data signals
are connected to 3 I/O lines on the same external
pins. With these 3 lines, the SPI can operate in the
following operating modes: Software SPI, S-BUS,
I
C-bu
s and as a standard serial I/O (clock, data,
enable). An interrupt request can be generated af-
ter eight clock pulses. Figure 35. shows the SPI
block diagram.
The SCL line clocks, on the falling edge, the shift
register and the counter. To allow SPI operation in
slave mode, the SCL pin must be programmed as
input and an external clock must be supplied to
this pin to drive the SPI peripheral.
In master mode, SCL is programmed as output, a
clock signal must be generated by software to set
and reset the port line.
Figure 35. SPI Block Diagram
Set Res
CLK
RESET
4-Bit Counter
(Q4=High after Clock8)
Data Reg
Direction
I/O Port
8-Bit Data
Shift Register
Reset
Load
DOUT
Output
Enable
8-Bit Tristate Data I/O
RESET
I/O Port
I/O Port
CP
CP
DIN
D0............... .............D7
to Processor Data Bus
Q4
Q4
OPR Reg.
DIN
SCL
Sin
Sout
SPI Interrupt Disable Register
SPI Data Register
Data Reg
Direction
Data Reg
Direction
DOUT
Write
Read
M0
1
Interrupt
VR01504
58
相關PDF資料
PDF描述
ST6235BQ3 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, 16-BIT AUTO-RELOAD TIMER, EEPROM, SPI AND UART
ST6235BQ6 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, 16-BIT AUTO-RELOAD TIMER, EEPROM, SPI AND UART
ST623x-EMU2 Real Time Emulation Development Tools for ST6218/ST6228/ST623x MCUs(ST6218/6228/623x的實時開發工具)
ST6245BQ1 The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
ST62T45B The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
相關代理商/技術參數
參數描述
ST62E35BG1 功能描述:8位微控制器 -MCU UV EPROM 8K RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62E3X-EPB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EPROM PROGRAMMING BOARDS DATASHEET FOR ST62 FAMILY
ST62E3X-EPB/110 功能描述:程序設計器 - 基于處理器 ST62 EPROM Programmr RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
ST62E40 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GANG PROGRAMMERS FOR ST62 MCU FAMILY
ST62E40B 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCU WITH LCD DRIVER, EEPROM AND A/D CONVERTER