- 您現在的位置：買賣IC網 > PDF目錄383838 > ST20GP6 MAX 7000 CPLD 256 MC 208-RQFP PDF資料下載
參數資料
| 型號： | ST20GP6 |
| 英文描述： | MAX 7000 CPLD 256 MC 208-RQFP |
| 中文描述： | GPS處理器 |
| 文件頁數： | 75/116頁 |
| 文件大小： | 1107K |
| 代理商： | ST20GP6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
ST20-GP1
75/116
Figure 13.3 9-bit data frames
Transmission
Transmission begins at the next overflow of the divide-by-16 counter (see Figure 13.3 above),
provided that the
Run
bit is set and data has been loaded into the
ASCTxBuffer
. The transmitted
data frame consists of three basic elements:
the start bit
the data field (8 or 9 bits, least significant bit (LSB) first, including a parity bit, if selected)
the stop bits (0.5, 1, 1.5 or 2 stop bits)
Data transmission is double buffered. When the transmitter is idle, the transmit data written into the
transmit buffer is immediately moved to the transmit shift register, thus freeing the transmit buffer
for the next data to be sent. This is indicated by the transmit buffer empty flag (
TxBufEmpty
) being
set. The transmit buffer can be loaded with the next data, while transmission of the previous data is
still going on.
The transmitter empty flag (
TxEmpty
) will be set at the beginning of the last data frame bit that is
transmitted, i.e. during the first system clock cycle of the first stop bit shifted out of the transmit shift
register.
Reception
Reception is initiated by a falling edge on the data input pin (
RXD
), provided that the
Run
and
RxEnable
bits are set. The
RXD
pin is sampled at 16 times the rate of the selected baud rate. A
majority decision of the first, second and third samples of the start bit determines the effective bit
value. This avoids erroneous results that may be caused by noise.
If the detected value is not a 0 when the start bit is sampled, the receive circuit is reset and waits
for the next falling edge transition of the
RXD
pin. If the start bit is valid, the receive circuit
continues sampling and shifts the incoming data frame into the receive shift register. For
subsequent data and parity bits, the majority decision of the seventh, eighth and ninth samples in
each bit time is used to determine the effective bit value.
For 0.5 stop bits, the majority decision of the third, fourth, and fifth samples during the stop bit is
used to determine the effective stop bit value.
For 1 and 2 stop bits, the majority decision of the seventh, eighth, and ninth samples during the
stop bits is used to determine the effective stop bit values.
1st
stop
bit
2nd
stop
bit
start
bit
D0
(LSB)
D1
D2
D3
D4
D5
D6
9th
bit
D7
Data bit (
D8
)
Parity bit
Wake-up bit
相關PDF資料 |
PDF描述 |
|---|---|
| ST25C02AB1 | IC FLEX 6000 FPGA 16K 144-TQFP |
| ST25C02AB6 | Stratix FPGA 25K FBGA-672 |
| ST25C02AM1 | IC ACEX 1K FPGA 100K 208-PQFP |
| ST25C02AM6 | Cyclone II FPGA 20K FBGA-256 |
| ST25C04ML1 | IC FLEX 6000 FPGA 24K 144-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST20-GP6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
| ST20GP6CT33S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
| ST20GP6CX33S | 功能描述:射頻無線雜項 GPS Processor RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| ST20GP6CX33STR | 功能描述:射頻無線雜項 GPS Processor RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| ST20GP6X33S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
發布緊急采購，3分鐘左右您將得到回復。