參數資料
型號: ST20Cx
廠商: 意法半導體
英文描述: Instruction Set Reference Manual
中文描述: 指令集參考手冊
文件頁數: 191/212頁
文件大小: 647K
代理商: ST20CX
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁當前第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁
8/212
This section also describes any situations where the operation of the instruction is
undefined or invalid.
Example
Using the
add instruction as an example again, the comments listed are:
Comments:
Secondary instruction.
This says that
add is a secondar y instruction.
1.7
Notation
The following sections give a full description of the notation used in the ‘definition’
section of the instruction descriptions.
1.7.1
The processor state
The processor state consists of the registers (mainly Areg, Breg, Creg, Iptr, and
Wptr), the contents of memory, and various flags and special registers (such as the
error flags , process queue pointers, clock registers, etc.).
The Wptr register is used for the address of the workspace of the current process.
This address is word aligned and therefore has the two least significant bits set to
zero. Wdesc is used for the ‘process descriptor’ — the value that is held in memory as
an identifier of the process when the process is not being executed. This value is
composed of the top 31 bits of the Wptr plus the process priority stored in bit 0 of the
word. Bit 0 is set to 0 for high priority processes and 1 for low priority processes. Bit 1
of the process descriptor is always 0.
1.7.2
General
The instruction descriptions are not intended to describe the way the instructions are
implemented, but only their effect on the state of the processor. So, for example, the
block move instructions are described in terms of a sequence of
byte reads and writes
even though the instructions are implemented to perform the minimum number of
word reads and writes.
Comments (in
italics) are used to both clarify the description and to describe actions
or values that cannot easily be represented by the notation used here; e.g.
start next
process. These actions may be performed in another subsystem in the device, such
as the communications subsystem, and so any changes to machine state are not
necessarily completely synchronized with the execution of the instruction (as the
different subsystems work independently and in parallel).
Ellipses are used to show a range of values; e.g. ‘i = 0..31’ means that i has
values from 0 to 31, inclusive.
相關PDF資料
PDF描述
ST223C04CCP0L 745 A, 400 V, SCR, TO-200AB
ST223C04CCP0 745 A, 400 V, SCR, TO-200AB
ST223C04CCP1L 745 A, 400 V, SCR, TO-200AB
ST223C04CCP1 745 A, 400 V, SCR, TO-200AB
ST223C04CCP2L 745 A, 400 V, SCR, TO-200AB
相關代理商/技術參數
參數描述
ST20GP1 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GPS PROCESSOR
ST20-GP1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR
ST20GP1X33S 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR
ST20GP6 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GPS PROCESSOR
ST20-GP6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR