參數資料
型號： SPAKDSP311VL150
廠商： Freescale Semiconductor
文件頁數： 21/96頁
文件大小： 0K
描述： IC DSP 24BIT 150MHZ 196-MAPBGA
標準包裝： 2
系列： DSP56K/Symphony
類型： 定點
接口： 主機接口，SSI，SCI
時鐘速率： 150MHz
非易失內存： ROM（576 B）
芯片上RAM： 384kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.80V
工作溫度： -40°C ~ 100°C
安裝類型： 表面貼裝
封裝/外殼： 196-LBGA
供應商設備封裝： 196-MAPBGA（15x15）
包裝： 托盤
DSP56311 Technical Data, Rev. 8
2-8
Freescale Semiconductor
Specifications
26
Duration of level sensitive IRQA assertion to ensure interrupt service
(when exiting Stop)
2, 3
PLL is not active during Stop (PCTL Bit 17 = 0) and Stop delay is
enabled
(Operating Mode Register Bit 6 = 0)
PLL is not active during Stop (PCTL Bit 17 = 0) and Stop delay is
not enabled
(Operating Mode Register Bit 6 = 1)
PLL is active during Stop (PCTL Bit 17 = 1) (implies no Stop delay)
Minimum:
PLC
× ET
C × PDF + (128K
PLC/2)
× TC
PLC
× ET
C × PDF +
(20.5
± 0.5) × TC
5.5
× T
C
13.6
12.3
36.7
—
ms
ns
27
Interrupt Request Rate
HI08, ESSI, SCI, Timer
DMA
IRQ, NMI (edge trigger)
IRQ, NMI (level trigger)
Maximum:
12
× T
C
8
× TC
8
× TC
12
× T
C
—
80.0
53.3
80.0
ns
28
DMA Request Rate
Data read from HI08, ESSI, SCI
Data write to HI08, ESSI, SCI
Timer
IRQ, NMI (edge trigger)
Maximum:
6
× T
C
7
× TC
2
× TC
3
× T
C
—
40.0
46.7
13.3
20.0
ns
29
Delay from IRQA, IRQB, IRQC, IRQD, NMI assertion to external
memory (DMA source) access address out valid
Minimum:
4.25
× T
C + 2.0
30.3
—
ns
Notes:
1.
When fast interrupts are used and IRQA, IRQB, IRQC, and IRQD are defined as level-sensitive, timings 19 through 21 apply to
prevent multiple interrupt service. To avoid these timing restrictions, the deasserted Edge-triggered mode is recommended
when fast interrupts are used. Long interrupts are recommended for Level-sensitive mode.
2.
This timing depends on several settings:
For PLL disable, using internal oscillator (PLL Control Register (PCTL) Bit 16 = 0) and oscillator disabled during Stop (PCTL
Bit 17 = 0), a stabilization delay is required to assure that the oscillator is stable before programs are executed. Resetting the
Stop delay (Operating Mode Register Bit 6 = 0) provides the proper delay. While Operating Mode Register Bit 6 = 1 can be set,
it is not recommended, and these specifications do not guarantee timings for that case.
For PLL disable, using internal oscillator (PCTL Bit 16 = 0) and oscillator enabled during Stop (PCTL Bit 17=1), no
stabilization delay is required and recovery is minimal (Operating Mode Register Bit 6 setting is ignored).
For PLL disable, using external clock (PCTL Bit 16 = 1), no stabilization delay is required and recovery time is defined by the
PCTL Bit 17 and Operating Mode Register Bit 6 settings.
For PLL enable, if PCTL Bit 17 is 0, the PLL is shutdown during Stop. Recovering from Stop requires the PLL to get locked.
The PLL lock procedure duration, PLL Lock Cycles (PLC), may be in the range of 0 to 1000 cycles. This procedure occurs in
parallel with the stop delay counter, and stop recovery ends when the last of these two events occurs. The stop delay counter
completes count or PLL lock procedure completion.
PLC value for PLL disable is 0.
The maximum value for ETC is 4096 (maximum MF) divided by the desired internal frequency (that is, for 66 MHz it is 4096/66
MHz = 62
s). During the stabilization period, TC, TH, and TL is not constant, and their width may vary, so timing may vary as
well.
3.
Periodically sampled and not 100 percent tested.
4.
Value depends on clock source:
For an external clock generator, RESET duration is measured while RESET is asserted, VCC is valid, and the EXTAL input is
active and valid.
For an internal oscillator, RESET duration is measured while RESET is asserted and VCC is valid. The specified timing
reflects the crystal oscillator stabilization time after power-up. This number is affected both by the specifications of the crystal
and other components connected to the oscillator and reflects worst case conditions.
When the VCC is valid, but the other “required RESET duration” conditions (as specified above) have not been yet met, the
device circuitry is in an uninitialized state that can result in significant power consumption and heat-up. Designs should
minimize this state to the shortest possible duration.
5.
If PLL does not lose lock.
6.
VCCQH = 3.3 V ± 0.3 V, VCC = 1.8 V ± 0.1 V; TJ = –40°C to +100°C, CL = 50 pF.
7.
WS = number of wait states (measured in clock cycles, number of TC).
8.
Use expression to compute maximum value.
Table 2-7.
Reset, Stop, Mode Select, and Interrupt Timing6 (Continued)
No.
Characteristics
Expression
150 MHz
Unit
Min
Max
相關PDF資料
PDF描述
VE-24T-CW-F1 CONVERTER MOD DC/DC 6.5V 100W
VE-24P-CW-F3 CONVERTER MOD DC/DC 13.8V 100W
VE-2TR-CW-F4 CONVERTER MOD DC/DC 7.5V 100W
VI-25B-CY-S CONVERTER MOD DC/DC 95V 50W
TPSD156M025R0100 CAP TANT 15UF 25V 20% 2917
相關代理商/技術參數
參數描述
SPAKDSP321VF240 功能描述:IC DSP 24BIT 196-MAPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:DSP56K/Symphony 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
SPAKDSP321VF275 功能描述:IC DSP 24BIT 196-MAPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:DSP56K/Symphony 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
SPAKDSP321VL240 功能描述:IC DSP 24BIT 240MHZ 196-MAPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:DSP56K/Symphony 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
SPAKDSP321VL275 功能描述:IC DSP 24BIT 275MHZ 196-MAPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:DSP56K/Symphony 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
SPAKDSP56824BU70 制造商:Freescale Semiconductor 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*