- 您現在的位置：買賣IC網 > PDF目錄384921 > SMH4804 (Summit Microelectronics, Inc.) -48V Programmable Hot Swap Sequencing Power Controller PDF資料下載
參數資料
| 型號： | SMH4804 |
| 廠商： | Summit Microelectronics, Inc. |
| 英文描述： | -48V Programmable Hot Swap Sequencing Power Controller |
| 中文描述： | - 48V的可編程序熱插拔電源控制器 |
| 文件頁數： | 7/41頁 |
| 文件大?。?/td> | 574K |
| 代理商： | SMH4804 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
SMH4804
Functional Description
Summit Microelectronics
2050 3.7 10/30/02
7
Current regulation is generally enabled in applications that
have switched dual (A and B) distributed power sources. By
using the current regulation function, unwarranted
shutdowns can be avoided if one of the dual supplies is
switched in when it is at a more negative potential the
currently operating supply.
When current regulation is selected by programming bits
1:0 of Register 6 to a binary value of 01 (5 ms), 10 (80 ms),
or 11 (160 ms), it is enabled during a soft-start (power on
period) and during normal operation after the PG[4:1]#
outputs are enabled. If the voltage monitored at the
CBSENSE pin is greater than 50mV, but less than 60mV,
the SMH4804 reduces the VGATE voltage in order to
maintain a CBSENSE potential less than 60mV, effectively
regulating the current through the MOSFET.
Figure 8 and Figure 9 illustrate the current regulation
function. The time period t
PCR
— selectable at 5, 80, or 160
ms — is the maximum time during which regulation is
enforced. If either V
QCB
or t
PCR
are exceeded the VGATE
and PG[4:1]# outputs are immediately deasserted.
However, if CBSENSE drops below 50mV before the timer
period ends, the timer is reset and VGATE resumes normal
operation (see Current Regulation With Recovery on page
7). If the Quick-Trip level is exceeded, the device bypasses
the current regulation timer and shuts down immediately.
The current regulation feature is disabled in the default
configuration.
Figure 8. Current Regulation With Recovery
Figure 9. Current Regulation Without Recovery
Nonvolatile Fault Latch
The SMH4804 provides an optional nonvolatile fault latch
(NVFL) circuit breaker feature. The nonvolatile fault latch
essentially provides a programmable fuse on the circuit
breaker. When the latch is enabled by setting bit 5 of
Register 5, the nonvolatile fault latch is set whenever the
circuit breaker trips. Once set, it cannot be reset by cycling
power or through the use of the RESET# pin.
Note: The device remains disabled until Register C is
reprogrammed. Refer to Register C - Address 1100 on page
38 for more information.
As long as the NVFL is set, the FAULT# output remains
asserted. The Nonvolatile Fault Latch feature is disabled in
the default configuration.
Resetting FAULT#
When the circuit breaker trips, the VGATE output is turned
off and the SMH4804 drives FAULT# low. There are two
methods to reset the circuit breaker which are selectable
with the MODE pin:
When the MODE is held high or left floating, the circuit
breaker is in the duty-cycle mode. In this case the
breaker resets automatically after a time of t
CYC
.
When the MODE pin is held low (or disabled in the
Configuration Register) FAULT# can be reset by
bringing RESET# low. The VGATE output attempts to
restart the MOSFET slew control circuitry t
PDD
after
bringing RESET# back high again.
In either case, cycling power to the board resets the circuit
breaker. If the over current condition still exists after the
MOSFET switches back on, the circuit breaker will re-trip.
2050 Fig06a
V
QCB
VGATE
t
CRD
50mV
0V
CBSENSE
t
PCR
<t
12V
0V
2050 Fig06b
V
QCB
VGATE
50mV
0V
CBSENSE
t
PCR
12V
0V
相關PDF資料 |
PDF描述 |
|---|---|
| SMH4812 | Distributed Power Hot-Swap Controller |
| SMH4812G | Distributed Power Hot-Swap Controller |
| SMH4812S | Distributed Power Hot-Swap Controller |
| SMH4814 | Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814NCR00 | Dual Feed Active-ORing Programmable Hot Swap Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMH4804F | 制造商:SUMMIT 功能描述: |
| SMH4811 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DISTRIBUTED POWER HOT SWAP CONTROLLER |
| SMH4811A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DISTRIBUTED POWER HOT SWAP CONTROLLER |
| SMH4811A_09 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Programmable Distributed Power Hot-Swap Controller for High-Availability Systems |
| SMH4811AG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DISTRIBUTED POWER HOT SWAP CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。