參數資料
型號： SMH4804
廠商： Summit Microelectronics, Inc.
英文描述： -48V Programmable Hot Swap Sequencing Power Controller
中文描述： - 48V的可編程序熱插拔電源控制器
文件頁數： 20/41頁
文件大?。?/td> 574K
代理商： SMH4804
Timing Diagram
SMH4804
20
2050 3.7 10/30/02
Summit Microelectronics
Operating at High Voltages
The breakdown voltage of the external active and passive
components limits the maximum operating voltage of the
SMH4804 hot-swap controller. Components that must be
able to withstand the full supply voltage are: the input and
output decoupling capacitors, the protection diode in series
with the DRAIN SENSE pin, the power MOSFET switch and
the capacitor connected between its drain and gate, the
high-voltage transistors connected to the power good
outputs, and the dropper resistor connected to the
controller’s V
DD
pin.
Over-Voltage and Under-Voltage Resistors
In Figures 21, 22, and 23, the three resistors (R1, R2, and
R3) connected to the OV and UV inputs must be capable of
withstanding the maximum supply voltage of several
hundred volts. The trip voltage of the UV and OV inputs is
2.5V relative to V
SS.
As the input impedance of UV and OV
is very high, large value resistors can be used in the
resistive divider. The divider resistors should be high
stability, 1% metal-film resistors to keep the under-voltage
and over-voltage trip points accurate.
Telecom Design Example
A hot-swap telecom application may use a 48V power
supply with a –25% to +50% tolerance (i.e., the 48V supply
can vary from 36V to 72V). The formula for calculating R1,
R2, and R3 are as follows.
First, a peak current, ID
MAX
,
must be specified for the
resistive network. The value of the current is arbitrary, but it
cannot be too high (self-heating in R3 becomes a problem),
or too low (the value of R3 becomes very large, and leakage
currents can reduce the accuracy of the OV and UV trip
points). The value of IDMAX should be
≥
200μA for the best
accuracy at the OV and UV trip points. A value of 250μA for
IDMAX is used to illustrate the following calculations.
With V
OV
(2.5V) being the over-voltage trip point, R1 is
calculated by the formula:
Substituting:
Next the minimum current that flows through the resistive
divider, ID
MIN
,
is calculated from the ratio of minimum and
maximum supply voltage levels
:
Substituting:
Now the value of R3 is calculated from ID
MIN
:
V
UV
is the under-voltage trip point, also 2.5V. Substituting:
The closest standard 1% resistor value is 267 k
Then R2 is calculated:
or
Substituting:
An Excel spread sheet is available on Summit's website
(
www.summitmicro.com)
to simplify the resistor value
calculations and tolerance analysis for R1, R2, and R3.
Dropper Resistor Selection
The SMH4804 is powered from the high-voltage supply via
a dropper resistor, R
D
. The dropper resistor must provide
the SMH4804 (and its loads) with sufficient operating
current under minimum supply voltage conditions, but must
R1 =
V
OV
ID
MAX
R1 =
2.5V
250
μ
A
= 10 K
ID
MIN
= ID
MAX
x VS
MIN
VS
MAX
ID
MIN
=
A x 36V= 125
250
μ
μΑ
R3 = VS
MIN
x V
UV
ID
MIN
R3 = 3125
x 2.5V
μΑ
= 286 k
(R1 + R2) =
V
UV
ID
MIN
R2 =
V
UV
ID
MIN
- R1
R2 =
2.5V
125
μΑ
- 10 k
=
20 k
10 k
=
10 k
相關PDF資料
PDF描述
SMH4812 Distributed Power Hot-Swap Controller
SMH4812G Distributed Power Hot-Swap Controller
SMH4812S Distributed Power Hot-Swap Controller
SMH4814 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814NCR00 Dual Feed Active-ORing Programmable Hot Swap Controller
相關代理商/技術參數
參數描述
SMH4804F 制造商:SUMMIT 功能描述:
SMH4811 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DISTRIBUTED POWER HOT SWAP CONTROLLER
SMH4811A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DISTRIBUTED POWER HOT SWAP CONTROLLER
SMH4811A_09 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Programmable Distributed Power Hot-Swap Controller for High-Availability Systems
SMH4811AG 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DISTRIBUTED POWER HOT SWAP CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*