- 您現在的位置：買賣IC網 > PDF目錄16479 > SMARTPSE24-KIT (Silicon Laboratories Inc)KIT EVAL REF 24PORT SPI/UART PDF資料下載
參數資料
| 型號： | SMARTPSE24-KIT |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 18/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVAL REF 24PORT SPI/UART |
| 標準包裝： | 1 |
| 主要目的： | 電源管理，以太網供電（POE），PSE |
| 已用 IC / 零件： | Si3452，Si3482，Si3500 |
| 已供物品： | 板，線纜，CD |
| 相關產品： | SI3482-A01-GM-ND - IC CTLR POE 24-48PORT PSE 24-QFN 336-1830-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1835-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1829-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1831-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1834-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1844-5-ND - IC POE SWITCH PWR OVER LAN 20QFN 336-1833-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1832-5-ND - IC POE CONTROLLER MIDSPAN 40QFN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Si3452
Rev. 1.3
25
6. Operational Notes
6.1. Port Turn On
If the port is turned on by putting it in auto mode, the Si3452 will take care of all specified timing, and it will take
care of the two-event classification if the first event result is Class 4 and PoE+ mode is enabled. However, if
automatic mode operation is not desired after port turn-on, the port should be set to semi-auto or manual mode
once it has powered. In automatic mode, ICUT is set according to the classification result.
The port turn-on command is used to turn on a port in semi-auto or manual mode. If the port is turned on in semi-
auto mode, turn-on is delayed until the next detection and classification. If the detection or classification result is
not valid, the port will not power. If the classification is Class 4 and PoE+ mode is enabled, a 2-event classification
is given. ICUT setting is not automatic for port turn-on in semi-auto or manual mode.
If the port is turned on by putting it in manual mode, the normal sequence is to start with the port in semi-auto mode
and interrupt on a classification complete, which indicates that there is a valid PD signature and that a classification
result is available. Based on the classification result, the host can make a decision to apply power or not. The IEEE
standard requires that a port be powered within 400 ms of a valid detect complete. It is also desirable to power the
port prior to the start of the next detection pulse, which can occur in as little as 300 ms. Therefore, it is
recommended that ports be powered in under 250 ms from the class complete interrupt when using the manual
mode turn-on command.
Using manual mode turn-on, detection is not done prior to port turn on, but classification is always performed just
prior to port turn on. Ports are turned on in manual mode regardless of the classification result. 2-event
classification is performed if the first event result is Class 4 and the port is enabled for PoE+ mode. The manual
mode classification step does not generate a classification complete flag because it is assumed that the
classification was already done in semi-auto mode and the host has already made the decision to grant power.
During the initial 60 ms (Tstart) time of port turn-on, 1x current limit and ICUT = 375 mA (nominal) is enforced. After
Tstart, if the port is not overloaded, Pgood is set to true, and ICUT and 1x or 2x current limit will follow the I2C
register settings. In auto mode, the I2C registers are set according to the classification result, but, if desired, they
can be overwritten after Pgood becomes true. After Tstart, 2x current limit is always allowed if PoE+ mode is
enabled.
6.2. Changing the Interrupt Mask
The INT register and INT pin are always synchronized. However, there can be up to a 5 ms delay between an
event that causes or clears an interrupt and the update of the register and pin.
Thus, if the INT mask register is changed to clear an interrupt or to block an interrupt source, there can be up to a
5 ms delay between the change of the INT mask register and the resultant change in the INT register and INT pin.
Generally, use of the mask register to clear interrupts is not recommended; it is better to clear an interrupt by
reading the appropriate COR register.
6.3. Port Voltage and Current Measurements
Port current voltage and current are reported as of the time the measurement command is written to register 0x12.
Spikes of current or other momentary current changes are not filtered. It may be desirable to add a ~1 second
averaging filter to reported current when using port current information for power management decisions.
相關PDF資料 |
PDF描述 |
|---|---|
| LBC2518T681M | INDUCTOR WOUND 680UH 45MA 1007 |
| VE-24D-EX | CONVERTER MOD DC/DC 85V 75W |
| 1SMA5926BT3 | DIODE ZENER 11V 1.5W SMA |
| ST16C2550CQ-0B-EB | EVAL BOARD FOR ST16C2551 48TQFP |
| 9-6278032-5 | C/A MT-RJ/MT-RJ MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMARTRF06EBK | 功能描述:射頻開發工具 SMARTRF06 EVAL BRD RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| SMARTRFTRXEBK | 功能描述:EVAL BOARD SMART RF 制造商:texas instruments 系列:- 零件狀態:有效 類型:收發器 頻率:- 配套使用產品/相關產品:MSP430 所含物品:板，線纜 標準包裝:1 |
| SMARTSOCKET 575 TYPE D | 制造商:TIME MARK CORP SIGNALINE 功能描述:Nominal input voltage 575VAC, Max input voltage 635VAC |
| SMARTSTART-BAC-D | 制造商:IDEC Corporation 功能描述:PROGRAMMABLE LOGIC CONTROLLER, Accessory Type:Starter Kit, For Use With:FL1D Ser |
| SMARTSTART-BAC-E | 制造商:IDEC Corporation 功能描述:FL1E SMARTRELAY STARTER KIT 120-240VAC/DC BASE MODULE W/O LCD DISPLAY 制造商:IDEC Corporation 功能描述:STARTER KIT, AUTOMATION & PROCESS CONTRO 制造商:IDEC Corporation 功能描述:STARTER KIT, AUTOMATION & PROCESS CONTROL; No. of Inputs:12; No. of Outputs:12; Kit Contents:WindLGC 6.0 Software, FL1E-B12RCC and Serial Programming Cable; Supply Voltage Max:240VAC; Accessory Type:SmartRelay Starter Kit 制造商:IDEC Corporation 功能描述:FL1E-B12RCC, Windlgc Software And Programming Cable 制造商:IDEC CORPORATION 功能描述:FL1E SmartRelay Starter Kit |
發布緊急采購，3分鐘左右您將得到回復。