參數資料
型號： SDCFBI-30-101
廠商： SANDISK CORP
元件分類： 存儲控制器/管理單元
英文描述： FLASH MEMORY DRIVE CONTROLLER, XMA50
封裝： PC CARD-50
文件頁數： 96/124頁
文件大小： 769K
代理商： SDCFBI-30-101
CompactFlash Memory Card Product Manual
SanDisk CompactFlash Memory Card Product Manual 1999 SANDISK CORPORATION
73
Table 6-5 Features Supported
Feature
Operation
01H
Enable 8 bit data transfer.
55H
Disable Read Look Ahead.
66H
Disable Power on Reset (POR) establishment of defaults at Soft Reset.
69H
Accepted for backward compatibility with the SDP Series but has no impact on the CF Memory Card.
81H
Disable 8 bit data transfer.
96H
Accepted for backward compatibility with the SDP Series but has no impact on the CF Memory Card.
9AH
Set the host current source capability. Allows tradeoff between current drawn and read/write speed.
BBH
4 bytes of data apply on Read/Write Long commands.
CCH
Enable Power on Reset (POR) establishment of defaults at Soft Reset.
Features 01H and 81H are used to enable and clear
8 bit data transfer mode. If the 01H feature com-
mand is issued, all data transfers will occur on t h e
low order D7-D0 data bus and the IOIS16 signal
will not be asserted for data register accesses.
Features 55H and BBH are the default features
for the CompactFlash Memory Card; thus, t h e
host does not have to issue this command with
these
features
unless
it
is
necessary
for
compatibility reasons.
The 9AH Feature is a CompactFlash Memory
Card unique option that provides a mechanism for
the host system to adjust how much current t h e
CompactFlash Card will use. The CompactFlash
Card reduces the current it draws by reducing its
operating frequency. This has the impact of also
reducing the performance of the CompactFlash
Card. The default for the CompactFlash Card
after a power on reset is to operate at the highest
performance and therefore the highest current
mode.
However
after
a
power
on,
t h e
CompactFlash Card will not draw more than its
minimum current as long as the host does not issue
any command which reads or writes to the flash
memory. This allows the host to issue the Set
Features command to set the desired power level
without exceeding the minimum requirement of
the CompactFlash Card.
To reduce the current the CompactFlash Memory
Card draws, the host issues the Set Features
command with the Feature register set to 9AH and
the Sector Count register (Config) set to a current
value which is equal to 4 mA times the value in
the Sector Count register. When this is done, t h e
controller will utilize a look-up table to program
the controllers frequency, microprocessors speed
and flash clocks with an optimum value to
provide
the
highest
performance
without
exceeding the hosts current limit. For example, i f
a host can supply 75 mA of current to t h e
CompactFlash Card, the Sector Count register
would be set to 75 divided by 4 (rounded down) or a
value of 18. The CompactFlash Card would then
automatically reduce its clock frequencies so that
it will not draw more than 75 mA (average, a t
nominal Vcc and room temperature) of current. I f
the host always wanted to operate at the lowest
possible current the Sector Count value should be
set to 1. The CompactFlash Card will then
operate at the lowest possible current (and also
the lowest performance).
At the completion of this command, the controller
will update the Cylinder Low register with t h e
controllers minimum valid current value (i.e. t h e
minimum current with which the CompactFlash
Memory Card can operate) and the Cylinder High
register with the maximum current it will use (i.e.
the maximum current the CompactFlash Card
will draw at the highest performance level). The
controller will use its minimum value for any
Sector Count value which is less than its minimum
value. For example, if the Sector Count is set to 4
which is equivalent to 16 mA, the controller will
operate at the lowest possible power point but
will not reject the command. Similarly
t h e
controller will use its maximum value for any
Sector Count value which is more than t h e
maximum current it can use.
There is no error associated with the 9AH feature.
Features 66H and CCH can be used to enable and
disable whether the Power On Reset (POR)
Defaults will be set when a soft reset occurs. The
default setting is to revert to the POR defaults
when a soft reset occurs. POR defaults the number
of heads and sectors along with 16 bit data
transfers and the read/write multiple block count.
相關PDF資料
PDF描述
SDD-3-023 SLIDE DIP SWITCH-3SWITCHES, DPST, MOMENTARY,THROUGH HOLE-STRAIGHT
SDD-6-023 SLIDE DIP SWITCH-6SWITCHES, DPST, MOMENTARY,THROUGH HOLE-STRAIGHT
SDC-5-023 SLIDE DIP SWITCH-5SWITCHES, SPDT, MOMENTARY,THROUGH HOLE-STRAIGHT
SDF330JABEGD1Z 5.5 A, 400 V, 1.1 ohm, N-CHANNEL, Si, POWER, MOSFET
SDF350JAAEHD1B 15 A, 400 V, 0.3 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-254AA
相關代理商/技術參數
參數描述
SDCFCF-001G-388 功能描述:COMPACT FLASH IND 1GB FIXED RoHS:是 類別:存儲卡，模塊 >> 存儲器，PC 卡 系列:- 標準包裝:30 系列:- 存儲容量:8GB 存儲器類型:存儲卡 - Extreme III SD?
SDCFCF-002G-388 功能描述:COMPACT FLASH IND 2GB FIXED RoHS:是 類別:存儲卡，模塊 >> 存儲器，PC 卡 系列:- 標準包裝:30 系列:- 存儲容量:8GB 存儲器類型:存儲卡 - Extreme III SD?
SDCFCF-004G-388 功能描述:COMPACT FLASH IND 4GB FIXED RoHS:是 類別:存儲卡，模塊 >> 存儲器，PC 卡 系列:- 標準包裝:30 系列:- 存儲容量:8GB 存儲器類型:存儲卡 - Extreme III SD?
SDCFCF-008G-388 功能描述:COMPACT FLASH IND 8GB FIXED RoHS:是 類別:存儲卡，模塊 >> 存儲器，PC 卡 系列:- 標準包裝:30 系列:- 存儲容量:8GB 存儲器類型:存儲卡 - Extreme III SD?
SDCFCF-016G-388 功能描述:COMPACT FLASH IND 16GB FIXED RoHS:是 類別:存儲卡，模塊 >> 存儲器，PC 卡 系列:- 標準包裝:30 系列:- 存儲容量:8GB 存儲器類型:存儲卡 - Extreme III SD?
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*