- 您現在的位置：買賣IC網 > PDF目錄3765 > SC16IS752IBS,151 (NXP Semiconductors)IC UART DUAL I2C/SPI 32-HVQFN PDF資料下載
參數資料
| 型號： | SC16IS752IBS,151 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 56/60頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART DUAL I2C/SPI 32-HVQFN |
| 產品培訓模塊： | Bridge Solutions Stand-Alone UARTs I²C Bus Fundamentals |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 490 |
| 特點： | 低電流 |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.5V, 3.3V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-HVQFN（5x5） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 828 (CN2011-ZH PDF) |
| 配用： | 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART 568-3510-ND - DEMO BOARD SPI/I2C TO UART |
| 其它名稱： | 568-2236 935279288151 SC16IS752IBS-S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁
SC16IS752_SC16IS762
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 9 — 22 March 2012
6 of 60
NXP Semiconductors
SC16IS752; SC16IS762
Dual UART with I2C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
6.2 Pin description
Table 2.
Pin description
Symbol
Pin
Type
Description
TSSOP28
HVQFN32
CS/A0
10
7
I
SPI chip select or I2C-bus device address select A0. If SPI configuration
is selected by I2C/SPI pin, this pin is the SPI chip select pin
(Schmitt-trigger active LOW). If I2C-bus configuration is selected by
I2C/SPI pin, this pin along with A1 pin allows user to change the device’s
base address.
To select the device address, please refer to Table 32.
CTSA
2
31
I
UART clear to send (active LOW), channel A. A logic 0 (LOW) on the
CTSA pin indicates the modem or data set is ready to accept transmit
data from the SC16IS752/SC16IS762. Status can be tested by reading
MSR[4]. This pin only affects the transmit and receive operations when
Auto-CTS function is enabled via the Enhanced Features Register
EFR[7] for hardware flow control operation.
CTSB
16
15
I
UART clear to send (active LOW), channel B. A logic 0 on the CTSB pin
indicates the modem or data set is ready to accept transmit data from the
SC16IS752/SC16IS762. Status can be tested by reading MSR[4]. This
pin only affects the transmit and receive operations when Auto-CTS
function is enabled via the Enhanced Features Register EFR[7] for
hardware flow control operation.
I2C/SPI
96
I
I2C-bus or SPI interface select. I2C-bus interface is selected if this pin is
at logic HIGH. SPI interface is selected if this pin is at logic LOW.
IRQ
15
14
O
Interrupt (open-drain, active LOW). Interrupt is enabled when interrupt
sources are enabled in the Interrupt Enable Register (IER). Interrupt
conditions include: change of state of the input pins, receiver errors,
available receiver buffer data, available transmit buffer space, or when a
modem status flag is detected. An external resistor (1 k
for 3.3 V,
1.5 k
for 2.5 V) must be connected between this pin and V
DD.
SI/A1
11
8
I
SPI data input pin or I2C-bus device address select A1. If SPI
configuration is selected by I2C/SPI pin, this is the SPI data input pin. If
I2C-bus configuration is selected by I2C/SPI pin, this pin along with the
A0 pin allows user to change the slave base address. To select the
device address, please refer to Table 32.
SO
12
9
O
SPI data output pin. If SPI configuration is selected by I2C/SPI pin, this is
a 3-stateable output pin. If I2C-bus configuration is selected by the
I2C/SPI pin, this pin is undefined and must be left as not connected.
SCL/SCLK
13
10
I
I2C-bus or SPI input clock.
SDA
14
11
I/O
I2C-bus data input/output, open-drain if I2C-bus configuration is selected
by I2C/SPI pin. If SPI configuration is selected, this is not used and must
be connected to VSS.
GPIO0/DSRB
18
17
I/O
Programmable I/O pin or modem DSRB[1]
GPIO1/DTRB
19
18
I/O
Programmable I/O pin or modem DTRB[1]
GPIO2/CDB
20
19
I/O
Programmable I/O pin or modem CDB[1]
GPIO3/RIB
21
20
I/O
Programmable I/O pin or modem RIB[1]
GPIO4/DSRA
25
24
I/O
Programmable I/O pin or modem DSRA[2]
GPIO5/DTRA
26
25
I/O
Programmable I/O pin or modem DTRA[2]
GPIO6/CDA
27
26
I/O
Programmable I/O pin or modem CDA[2]
GPIO7/RIA
28
27
I/O
Programmable I/O pin or modem RIA[2]
相關PDF資料 |
PDF描述 |
|---|---|
| SC16IS752IPW,112 | IC UART DUAL 12C/SPI 28TSSOP |
| SC16C850IBS,151 | IC UART SGL-CH 3.3V 32-HVQFN |
| SC16IS760IPW,112 | IC UART 64BYTE 24TSSOP |
| FT2232HL-REEL | IC USB HS DUAL UART/FIFO 64-LQFP |
| ATMEGA168P-20AUR | MCU AVR 16K FLASH 20MHZ 32-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16IS752IBS-F | 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16IS752IPW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC16IS752IPW,112 | 功能描述:UART 接口集成電路 UART DUAL 12C/SPI RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16IS752IPW,128 | 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16IS752IPW112 | 制造商:NXP Semiconductors 功能描述:IC DUAL UART FIFO 5MBPS 3.6V TSSOP28 |
發布緊急采購，3分鐘左右您將得到回復。