參數資料
型號： SC16C654IB64,128
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64
封裝： 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64
文件頁數： 21/52頁
文件大?。?/td> 647K
代理商： SC16C654IB64,128
Philips Semiconductors
SC16C654/654D
Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 04 — 19 June 2003
28 of 52
9397 750 11617
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
5
MCR[5]
Xon Any.
Logic 0 = Disable Xon Any function (for 16C550 compatibility)
(normal default condition).
Logic 1 = Enable Xon Any function. In this mode, any RX character
received will enable Xon
4
MCR[4]
Loop-back. Enable the local loop-back mode (diagnostics). In this
mode the transmitter output (TX) and the receiver input (RX), CTS,
DSR, CD, and RI are disconnected from the SC16C654/654D I/O
pins. Internally the modem data and control pins are connected into a
loop-back data conguration (see Figure 8). In this mode, the receiver
and transmitter interrupts remain fully operational. The Modem
Control Interrupts are also operational, but the interrupts’ sources are
switched to the lower four bits of the Modem Control. Interrupts
continue to be controlled by the IER register.
Logic 0 = Disable loop-back mode (normal default condition).
Logic 1 = Enable local loop-back mode (diagnostics).
3
MCR[3]
OP2, INTx enable. Used to control the modem CD signal in the
loop-back mode.
Logic 0 = Forces INTA-INTD outputs to the 3-State mode during
the 16 mode (normal default condition). In the loop-back mode,
sets OP2 (CD) internally to a logic 1.
Logic 1 = Forces the INTA-INTD outputs to the active mode during
the 16 mode. In the loop-back mode, sets OP2 (CD) internally to a
logic 0.
2
MCR[2]
OP1. This bit is used in the Loop-back mode only. In the loop-back
mode, this bit is used to write the state of the modem RI interface
signal via OP1.
1
MCR[1]
RTS
Logic 0 = Force RTS output to a logic 1 (normal default condition).
Logic1=Force RTS output to a logic 0.
Automatic RTS may be used for hardware ow control by enabling
EFR[6]. See Table 22.
0
MCR[0]
DTR
Logic 0 = Force DTR output to a logic 1 (normal default condition).
Logic 1 = Force DTR output to a logic 0.
Table 19:
Modem Control Register bits description…continued
Bit
Symbol
Description
相關PDF資料
PDF描述
SC16C654IA68,512 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68
SC18005CQ SPECIALTY MICROPROCESSOR CIRCUIT, PQFP144
SC18IS600IBS,151 I2C BUS CONTROLLER, PQCC24
SC18IS600IBS I2C BUS CONTROLLER, PQCC24
SC2200UCL-300 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432
相關代理商/技術參數
參數描述
SC16C750 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 64-byte FIFO
SC16C750B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
SC16C750BIA44 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C750BIA44,512 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C750BIA44,518 功能描述:UART 接口集成電路 1CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*