- 您現在的位置：買賣IC網 > PDF目錄98077 > SB80L186EC13 (INTEL CORP) 16-BIT, 13 MHz, MICROPROCESSOR, PQFP100 PDF資料下載
參數資料
| 型號： | SB80L186EC13 |
| 廠商： | INTEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, 13 MHz, MICROPROCESSOR, PQFP100 |
| 封裝： | SHRINK, QFP-100 |
| 文件頁數： | 35/57頁 |
| 文件大?。?/td> | 1573K |
| 代理商： | SB80L186EC13 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
80C186EC188EC 80L186EC188EC
DERATING CURVES
272434 – 13
Figure 14 Typical Output Delay Variations versus Load Capacitance
272434 – 14
Figure 15 Typical Rise and Fall Variations versus Load Capacitance
RESET
The processor will perform a reset operation any
time the RESIN pin is active The RESIN pin is syn-
chronized before it is presented internally which
means that the clock must be operating before a
reset can take effect From a power-on state RESIN
must be held active (low) in order to guarantee cor-
rect initialization of the processor Failure to pro-
vide RESIN while the device is powering up will
result in unspecified operation of the device
Figure 16 shows the correct reset sequence when
first applying power to the processor An external
clock connected to CLKIN must not exceed the VCC
threshold being applied to the processor This is nor-
mally not a problem if the clock driver is supplied
with the same VCC that supplies the processor
When attaching a crystal to the device RESIN must
remain active until both VCC and CLKOUT are stable
(the length of time is application specific and de-
pends on the startup characteristics of the crystal
circuit) The RESIN pin is designed to operate cor-
rectly using a RC reset circuit but the designer must
ensure that the ramp time for VCC is not so long that
RESIN is never sampled at a logic low level when
VCC reaches minimum operating conditions
Figure 17 shows the timing sequence when RESIN
is applied after VCC is stable and the device has
been operating Note that a reset will terminate all
activity and return the processor to a known operat-
ing state Any bus operation that is in progress at the
time RESIN is asserted will terminate immediately
(note that most control signals will be driven to their
inactive state first before floating)
While
RESIN
is
active
bus
signals
LOCK
A19S16ONCE and A1816 are configured as in-
puts and weakly held high by internal pullup transis-
tors Only A19ONCE can be overdriven to a low
and is used to enable the ONCE Mode Forcing
LOCK or A1816 low at any time while RESIN is low
is prohibited and will cause unspecified device oper-
ation
40
相關PDF資料 |
PDF描述 |
|---|---|
| SB80L186EB8 | 16-BIT, 8 MHz, MICROPROCESSOR, PQFP80 |
| SB83C196KD | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| SB83C196NP | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP100 |
| SB83C196NU50 | 16-BIT, MROM, 50 MHz, MICROCONTROLLER, PQFP100 |
| SB87C196NP | 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SB80L186EC-13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microprocessor |
| SB80L186EC16 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| SB80L186EC20 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| SB80L186EC25 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| SB80L188EA-13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microprocessor |
發布緊急采購，3分鐘左右您將得到回復。