- 您現在的位置：買賣IC網 > PDF目錄192295 > S25FL064A0LNAI00 (SPANSION LLC) 64M X 1 FLASH 3V PROM, PDSO16 PDF資料下載
參數資料
| 型號： | S25FL064A0LNAI00 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 64M X 1 FLASH 3V PROM, PDSO16 |
| 封裝： | 0.300 INCH, PLASTIC, MS-013AA, SOP-16 |
| 文件頁數： | 3/36頁 |
| 文件大?。?/td> | 1495K |
| 代理商： | S25FL064A0LNAI00 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
12
S25FL064A
S25FL064A_00_C3 June 29, 2007
Da ta
Sh e e t
7.
Device Operations
All Spansion SPI devices (S25FL-A) accept and output data in bytes (8 bits at a time).
7.1
Byte or Page Programming
Programming data requires two commands: Write Enable (WREN), which is one byte, and a Page Program
(PP) sequence, which consists of four bytes plus data. The Page Program sequence accepts from 1 byte up
to 256 consecutive bytes of data (which is the size of one page) to be programmed in one operation.
Programming means that bits can either be left at 0, or programmed from 1 to 0. Changing bits from 0 to 1
requires an erase operation. Before this can be applied, the bytes of the memory need to be first erased to all
1’s (FFh) before any programming.
7.2
Sector Erase / Bulk Erase
The Sector Erase (SE) and Bulk Erase (BE) commands set all the bits in a sector or the entire memory array
to 1. While bits can be individually programmed from a 1 to 0, erasing bits from 0 to 1 must be done on a
sector-wide (SE) or array-wide (BE) level.
7.3
Monitoring Write Operations Using the Status Register
The host system can determine when a Write Status Register, program, or erase operation is complete by
monitoring the Write in Progress (WIP) bit in the Status Register. The Read from Status Register command
provides the state of the WIP bit.
7.4
Active Power and Standby Power Modes
The device is enabled and in the Active Power mode when Chip Select (CS#) is Low. When CS# is high, the
device is disabled, but may still be in the Active Power mode until all program, erase, and Write Status
Register operations have completed. The device then goes into the Standby Power mode, and power
consumption drops to ISB. The Deep Power Down (DP) command provides additional data protection against
inadvertent signals. After writing the DP command, the device ignores any further program or erase
commands, and reduces its power consumption to IDP.
7.5
Status Register
The Status Register contains the status and control bits that can be read or set by specific commands
Write In Progress (WIP): Indicates whether the device is performing a Write Status Register, program or
erase operation.
Write Enable Latch (WEL): Indicates the status of the internal Write Enable Latch.
Block Protect (BP2, BP1, BP0): Non-volatile bits that define memory area to be software-protected
against program and erase commands.
Status Register Write Disable (SRWD): Places the device in the Hardware Protected mode when this bit
is set to 1 and the W# input is driven low. In this mode, the non-volatile bits of the Status Register (SRWD,
BP2, BP1, BP0) become read-only bits.
相關PDF資料 |
PDF描述 |
|---|---|
| S2684-254 | PHOTO DIODE |
| S2815S | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| S29AL032D70BAE000 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D70BAE002 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D90TFI042 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S25FL064K | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64-Mbit CMOS 3.0 Volt Flash Memory with 80-MHz SPI (Serial Peripheral Interface) Multi I/O Bus |
| S25FL064K0SMFI010 | 功能描述:閃存 IC 64MBIT CMOS 3V FL MEMORY 80-MHZ SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL064K0SMFI011 | 功能描述:閃存 IC 64MBIT CMOS 3V FL MEMORY 80-MHZ SPI RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S25FL064K0SMFI013 | 制造商:Spansion 功能描述:FLASH SERL-SPI 3V/3.3V 64MBIT - Bulk |
| S25FL064LABBHI020 | 功能描述:IC FLASH NOR 24FBGA 制造商:cypress semiconductor corp 系列:FL-L 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:64Mb （8M x 8） 時鐘頻率:108MHz 寫周期時間 - 字，頁:- 存儲器接口:SPI - 四 I/O， QPI 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:24-TBGA 供應商器件封裝:24-BGA（6x8） 標準包裝:338 |
發布緊急采購，3分鐘左右您將得到回復。