- 您現在的位置：買賣IC網 > PDF目錄98069 > S1D13305F00B 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60 PDF資料下載
參數資料
| 型號： | S1D13305F00B |
| 元件分類： | 顯示控制器 |
| 英文描述： | 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60 |
| 封裝： | QFP6-60 |
| 文件頁數： | 27/94頁 |
| 文件大?。?/td> | 541K |
| 代理商： | S1D13305F00B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
S1D13305 Series
EPSON
27
Technical Manual
8.2.1.13. AP
Defines the horizontal address range of the virtual screen.
APL is the least significant byte of the address.
Figure 8. AP and C/R relationship
8.2.2. SLEEP IN
Places the system in standby mode. This command has no
parameter bytes. At least one blank frame after receiving
this command, the S1D13305F halts all internal opera-
tions, including the oscillator, and enters the sleep state.
Figure 7. AP parameters
APL
AP7
AP6
AP5
AP4
AP3
AP2
AP1
AP0
APH
AP15
AP14
AP13
AP12
AP11
AP10
AP9
AP8
Table 8. Horizontal address range
Hex code
[AP] addresses
APH
APL
per line
0000
0
0001
1
↓↓↓↓
↓
0050
80
↓↓↓↓
↓
FFFE
216 – 2
FFFF
216 – 1
Display area
C/R
Display memory limit
AP
Blank data is sent to the X-drivers, and the Y-drivers have
their bias supplies turned off by the YDIS signal. Using
the YDIS signal to disable the Y-drivers guards against
any spurious displays.
The internal registers of the S1D13305 series maintain
their values during the sleep state. The display memory
control pins maintain their logic levels to ensure that the
display memory is not corrupted.
The S1D13305 series can be removed from the sleep state
by sending the SYSTEM SET command with only the P1
parameter. The DISP ON command should be sent next
to enable the display.
Figure 9. SLEEP IN instruction
1. The YDIS signal goes LOW between one and two
frames after the SLEEP IN command is received.
Since YDIS forces all display driver outputs to go to
the deselected output voltage, YDIS can be used as a
power-down signal for the LCD unit. This can be
done by having YDIS turn off the relatively high-
power LCD drive supplies at the same time as it
blanks the display.
2. Since all internal clocks in the S1D13305 series are
halted while in the sleep state, a DC voltage will be
applied to the LCD panel if the LCD drive supplies
remain on.
If reliability is a prime consideration, turn off the
LCD drive supplies before issuing the SLEEP IN
command.
3. Note that, although the bus lines become high imped-
ance in the sleep state, pull-up or pull-down resistors
on the bus will force these lines to a known state.
MSB
LSB
C
0
1
01001
1
INSTRUCTION SET
相關PDF資料 |
PDF描述 |
|---|---|
| S1D13305F00A | 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60 |
| S1D13600F00A | CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64 |
| S1D13700F02A100 | 320 X 240 PIXELS CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64 |
| S1D13706F00A | 320 X 240 PIXELS CRT OR FLAT PNL GRPH DSPL CTLR, PQFP100 |
| S1D13806F00A | CRT OR FLAT PNL GRPH DSPL CTLR, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1D13305F00B100 | 制造商:Epson Electronics America Inc 功能描述:LCD DRVR 3V/3.3V/5V 80-Pin TQFP |
| S1D13501F00A100 | 制造商:Epson Electronics America Inc 功能描述:LCD DRVR 3V/3.3V/5V 80-Pin TQFP |
| S1D13502F00B100 | 制造商:Epson Electronics America Inc 功能描述:LCD DRVR 3V/3.3V/5V 80-Pin TQFP |
| S1D13502F00B200 | 功能描述:LCD 驅動器 LCD CONTROLLER RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| S1D13503 | 制造商:EPSON 制造商全稱:EPSON 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。