- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63455F 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128 PDF資料下載
參數資料
| 型號： | S1C63455F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128 |
| 封裝： | PLASTIC, QFP5-128 |
| 文件頁數： | 60/119頁 |
| 文件大?。?/td> | 865K |
| 代理商： | S1C63455F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
S1C63455 TECHNICAL MANUAL
EPSON
37
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (I/O Ports)
4.6.2 Mask option
In the I/O ports, the output specification during output mode can be selected from either complementary
output or N-channel open drain output by mask option.
When N-channel open drain output is selected, do not apply a voltage exceeding the power supply
voltage to the port.
When using the I/O port P10–P13 as the serial interface input/output terminals, the input specification
for the terminals that are used for the serial interface input can be selected from either "normal input" or
"with Schmitt trigger input". This option is applied to the serial interface input terminals, and is fixed at
"normal input" when the terminals are used for the I/O port P10–P13.
The mask option also permits selection of whether the pull-up resistor is used or not during input mode.
They are selected in 4-bit units (P00–P03 and P10–P13).
When "without pull-up" during the input mode is selected, take care that the floating status does not
occur.
The pull-up resistor for input mode and output specification (complementary output or N-channel open
drain output) selected by mask option are effective even when I/O ports are used for input/output of the
serial interface.
4.6.3 I/O control registers and input/output mode
Input or output mode can be set for the I/O ports by writing data into the corresponding I/O control
registers IOCxx.
To set the input mode, write "0" to the I/O control register. When an I/O port is set to input mode, it
becomes high impedance status and works as an input port.
However, when the pull-up explained in the following section has been set by software, the input line is
pulled up only during this input mode.
To set the output mode, write "1" is to the I/O control register. When an I/O port is set to output mode , it
works as an output port, it outputs a high level (VDD) when the port output data is "1", and a low level
(VSS) when the port output data is "0".
If perform the read out in each mode; when output mode, the register value is read out, and when input
mode, the port value is read out.
At initial reset, the I/O control registers are set to "0", and the I/O ports enter the input mode.
The I/O control registers of the ports that are set as input/output for the serial interface can be used as
general purpose registers that do not affect the I/O control. (See Table 4.6.1.1.)
4.6.4 Pull-up during input mode
A pull-up resistor that operates during the input mode is built into each I/O port of the S1C63455. Mask
option can set the use or non-use of this pull-up.
The pull-up resistor becomes effective by writing "1" to the pull-up control register PULxx that corre-
sponds to each port, and the input line is pulled up during the input mode. When "0" has been written,
no pull-up is done.
At initial reset, the pull-up control registers are set to "1".
The pull-up control registers of the ports in which "without pull-up" have been selected can be used as
general purpose registers.
Even when "with pull-up" has been selected, the pull-up control registers of the ports, that are set as
output for the serial interface, can be used as general purpose registers that do not affect the pull-up
control. (See Table 4.6.1.1.)
The pull-up control registers of the port, that are set as input for the serial interface, function the same as
the I/O port.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63455D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 |
| S1C63458F0A0100 | MICROCONTROLLER, PQFP144 |
| S1C63466D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140 |
| S1C63466F | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144 |
| S1C63567F0A0100 | MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63653 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。
