- 您現在的位置：買賣IC網 > PDF目錄384884 > RF3133 (RF Monolithics, Inc.) QUAD-BAND GSM850/GSM/DCS/PCS POWER AMP MODULE PDF資料下載
參數資料
| 型號： | RF3133 |
| 廠商： | RF Monolithics, Inc. |
| 英文描述： | QUAD-BAND GSM850/GSM/DCS/PCS POWER AMP MODULE |
| 中文描述： | 四頻GSM850/GSM/DCS/PCS功率放大器模塊 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 196K |
| 代理商： | RF3133 |
2-473
RF3133
Rev A4 030527
Thermal Pad and Via Design
The PCB land pattern has been designed with a thermal pad that matches the exposed die paddle size on the bottom of
the device.
Thermal vias are required in the PCB layout to effectively conduct heat away from the package. The via pattern shown
has been designed to address thermal, power dissipation and electrical requirements of the device as well as accommo-
dating routing strategies.
The Via pattern used for the RFMD qualification is based on thru-hole vias with 0.203mm to 0.330mm finished hole size
on a 0.5mm to 1.2mm grid pattern with 0.025mm plating on via walls. If micro vias are used in a design, it is suggested
that the quantity of vias be increased by a 4:1 ratio to achieve similar results.
Stencil Design Recommendation
The stencil aperture are typically designed to match the pad size shown in the PCB Solder Mask pattern and are
reduced for an overall 20 percent reduction in pad area for each pad. This has yielded good solder joint results based on
volumes assembled during product introduction phase.
Critical parameters to consider for successful solder paste application include:
Accurate registration of the stencil to the PCB during printing.
Good release of stencil from the PCB after paste applied. This is improved with laser cut trapezoidal openings.
Proper storage and handling of solder paste based on solder paste vendor guidelines.
Frequent cleaning of the solder paste stencil to remove residual solder paste.
Stencil material recommendations: 5mil (0.127mm) thick stainless steel, laser cut stencils with trapezoidal openings to
promote easy release of solder paste.
Vias
0.203 mm to 0.330 mm
Finished Hole
0.5 mm to 1.2 mm Grid
Figure 2. Thermal Pad and Via Design (RFMD Qualification)
相關PDF資料 |
PDF描述 |
|---|---|
| RF3133PCBA | QUAD-BAND GSM850/GSM/DCS/PCS POWER AMP MODULE |
| RF3146 | QUAD-BAND GSM850/GSM900/DCS/PCS POWER AMP MODULE |
| RF3146PCBA | QUAD-BAND GSM850/GSM900/DCS/PCS POWER AMP MODULE |
| RF3146SB | QUAD-BAND GSM850/GSM900/DCS/PCS POWER AMP MODULE |
| RF3163 | 3V 900MHZ LINEAR POWER AMPLIFIER MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF3133_05 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:QUAD-BAND GSM850/GSM/DCS/PCS POWER AMP MODULE |
| RF3133PCBA | 制造商:RFM 制造商全稱:RF Monolithics, Inc 功能描述:QUAD-BAND GSM850/GSM/DCS/PCS POWER AMP MODULE |
| RF3133PCBA-41X | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:QUAD-BAND GSM850/GSM/DCS/PCS POWER AMP MODULE |
| RF313-5 | 功能描述:高頻/射頻繼電器 5V DC-6GHz .15W hi sensitivity RoHS:否 制造商:Omron Electronics 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 VDC 線圈類型:Non-Latching 頻率: 功耗:100 mW 端接類型:Solder Terminal 絕緣:20 dB to 30 dB at 1 GHz 介入損耗:0.2 dB at 1 GHz |
| RF313-5/G | 制造商:Teledyne Relays 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。