參數資料
型號: PIC12F519
廠商: Microchip Technology Inc.
英文描述: 8-Pin, 8-Bit Flash Microcontroller
中文描述: 8引腳,8位閃存微控制器
文件頁數: 49/88頁
文件大?。?/td> 802K
代理商: PIC12F519
2007 Microchip Technology Inc.
Preliminary
DS41319A-page 47
PIC12F519
8.9
Program Verification/Code
Protection
If the code protection bit has not been programmed, the
on-chip program memory can be read out for
verification purposes.
The first 64 locations and the last location (OSCCAL)
can be read, regardless of the code protection bit
setting.
The last memory location can be read regardless of the
code protection bit setting on the PIC12F519 device.
8.10
ID Locations
Four memory locations are designated as ID locations
where users can store checksum or other code
identification numbers. These locations are not
accessible during normal execution, but are readable
and writable during program/verify.
Use only the lower 4 bits of the ID locations and always
program the upper 8 bits as ‘
0
’s.
8.11
In-Circuit Serial Programming
The PIC12F519 device can be serially programmed
while in the end application circuit. This is simply done
with two lines for clock and data, and three other lines for
power, ground and the programming voltage. This
allows users to manufacture boards with unprogrammed
PIC12F519 device and then program the PIC12F519
device just before shipping the product. This also allows
the most recent firmware, or a custom firmware, to be
programmed.
The PIC12F519 device is placed into a Program/Verify
mode by holding the RB1 and RB0 pins low while rais-
ing the MCLR (V
PP
) pin from V
IL
to V
IHH
(see program-
ming specification). The RB1 pin becomes the
programming clock, and the RB0 pin becomes the
programming data. Both RB1 and RB0 pins are Schmitt
Trigger inputs in this mode.
After Reset, a 6-bit command is then supplied to the
device. Depending on the command, 14 bits of program
data are then supplied to or from the device, depending
if the command was a Load or a Read. For complete
details of serial programming, please refer to the
PIC12F519 Memory Programming Specification
,”
(DS41316).
A typical In-Circuit Serial Programming connection is
shown in Figure 8-12.
FIGURE 8-12:
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
External
Connector
Signals
To Normal
Connections
To Normal
Connections
PIC12F519
V
DD
V
SS
MCLR/V
PP
RB1
RB0
+5V
0V
V
PP
CLK
Data I/O
V
DD
相關PDF資料
PDF描述
PIC12F609 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities
PIC12F615 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities
PIC12HV609 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities
PIC12HV615 8-Pin Flash-Based, 8-Bit CMOS Microcontrollers
PIC16C505-04 14-Pin, 8-Bit CMOS Microcontroller
相關代理商/技術參數
參數描述
PIC12F519_08 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit Flash Microcontrollers
PIC12F519-E/MC 功能描述:8位微控制器 -MCU 15KB Flash Prgrm 64B 8MHz Intrnl Oscilatr RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC12F519-E/MS 功能描述:8位微控制器 -MCU 15KB Flash Prgrm 64B 8MHz Intrnl Oscilatr RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC12F519-E/P 功能描述:8位微控制器 -MCU 15KB Flash Prgrm 64B 8MHz Intrnl Oscilatr RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC12F519-E/SN 功能描述:8位微控制器 -MCU 15KB Flash Prgrm 64B 8MHz Intrnl Oscilatr RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT