參數資料
型號： PIC12F510
廠商： Microchip Technology Inc.
英文描述： 8/14-Pin, 8-Bit Flash Microcontroller
中文描述： 8/14-Pin，8位閃存微控制器
文件頁數： 43/114頁
文件大?。?/td> 908K
代理商： PIC12F510
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
2006 Microchip Technology Inc.
Preliminary
DS41268B-page 41
PIC12F510/16F506
6.1
Using Timer0 With An External
Clock
When an external clock input is used for Timer0, it must
meet certain requirements. The external clock require-
ment is due to internal phase clock (T
OSC
) synchroniza-
tion. Also, there is a delay in the actual incrementing of
Timer0 after synchronization.
6.1.1
EXTERNAL CLOCK
SYNCHRONIZATION
When no prescaler is used, the external clock input is
the same as the prescaler output. The synchronization
of an external clock with the internal phase clocks is
accomplished by sampling the prescaler output on the
Q2 and Q4 cycles of the internal phase clocks
(Figure 6-4). Therefore, it is necessary for T0CKI or the
comparator output to be high for at least 2T
OSC
(and a
small RC delay of 2Tt0H) and low for at least 2T
OSC
(and a small RC delay of 2Tt0H). Refer to the electrical
specification of the desired device.
When a prescaler is used, the external clock input is
divided by the asynchronous ripple counter-type
prescaler, so that the prescaler output is symmetrical.
For the external clock to meet the sampling require-
ment, the ripple counter must be taken into account.
Therefore, it is necessary for T0CKI or the comparator
output to have a period of at least 4T
OSC
(and a small
RC delay of 4Tt0H) divided by the prescaler value. The
only requirement on T0CKI or the comparator output
high and low time is that they do not violate the
minimum pulse width requirement of Tt0H. Refer to
parameters 40, 41 and 42 in the electrical specification
of the desired device.
6.1.2
TIMER0 INCREMENT DELAY
Since the prescaler output is synchronized with the
internal clocks, there is a small delay from the time the
external clock edge occurs to the time the Timer0
module is actually incremented. Figure 6-4 shows the
delay from the external clock edge to the timer
incrementing.
FIGURE 6-4:
TIMER0 TIMING WITH EXTERNAL CLOCK
6.2
Prescaler
An 8-bit counter is available as a prescaler for the
Timer0 module or as a postscaler for the Watchdog
Timer (WDT), respectively (see Figure 10-12). For sim-
plicity, this counter is being referred to as “prescaler”
throughout this data sheet.
The PSA and PS<2:0> bits (OPTION<3:0>) determine
prescaler assignment and prescale ratio.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g.,
CLRF 1,
MOVWF 1, BSF 1, x,
etc.) will clear the prescaler.
When assigned to WDT, a
CLRWDT
instruction will clear
the prescaler along with the WDT. The prescaler is
neither readable nor writable. On a Reset, the
prescaler contains all ‘
0
’s.
Increment Timer0 (Q4)
External Clock Input or
Prescaler Output
(2)
Q1
Q2
Q3 Q4
Q1
Q2
Q3 Q4
Q1
Q2
Q3 Q4
Q1
Q2
Q3 Q4
Small pulse
misses sampling
Timer0
T0
T0 + 1
T0 + 2
External Clock/Prescaler
Output After Sampling
(3)
(1)
Note 1:
Delay from clock input change to Timer0 increment is 3T
OSC
to 7T
OSC
. (Duration of Q = T
OSC
). Therefore, the error
in measuring the interval between two edges on Timer0 input = ±4T
OSC
max.
External clock if no prescaler selected; prescaler output otherwise.
The arrows indicate the points in time where sampling occurs.
2:
3:
Note:
The prescaler may be used by either the
Timer0 module or the WDT, but not both.
Thus, a prescaler assignment for the
Timer0 module means that there is no
prescaler for the WDT and vice-versa.
相關PDF資料
PDF描述
PIC12F519 8-Pin, 8-Bit Flash Microcontroller
PIC12F609 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities
PIC12F615 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities
PIC12HV609 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities
PIC12HV615 8-Pin Flash-Based, 8-Bit CMOS Microcontrollers
相關代理商/技術參數
參數描述
PIC12F510_07 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller
PIC12F510_13 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers
PIC12F510-E/L 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller
PIC12F510-E/LQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller
PIC12F510-E/LSQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*