參數資料
型號： PCD5008H
廠商： NXP SEMICONDUCTORS
元件分類： 尋呼電路
英文描述： FLEX Pager Decoder
中文描述： TELECOM, PAGING DECODER, PQFP32
封裝： 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-358-1, LQFP-32
文件頁數： 21/64頁
文件大?。?/td> 341K
代理商： PCD5008H
1998 Jun 17
21
Philips Semiconductors
Product specification
FLEX
Pager Decoder
PCD5008
8.5
Receiver control interface
8.5.1
G
ENERAL
The PCD5008 has 8 programmable receiver control lines,
S0 to S7. The host can program via SPI packets what
setting is applied to the receiver control lines, the duration
of warm-up and shut-down stages and the polling of the
LOBAT pin. This programmability allows the PCD5008 to
interface with many off-the-shelf receiver ICs. Note that
these packets are ignored when sent while decoding is
enabled (ON bit is set in the control packet).
8.5.2
L
OW BATTERY DETECTION
The PCD5008 can be configured to poll the LOBAT pin at
the end of every receiver control setting. This check can be
enabled or disabled for each receiver control setting. If the
poll is enabled for a setting, the pin is read just before the
PCD5008 activates the next setting on the receiver control
lines. The PCD5008 sends a status packet whenever the
value differs from the previous time that the LOBAT pin
was polled.
8.5.3
R
ECEIVER SETTINGS AT RESET
The receiver control ports are 3-state outputs which are set
to high impedance when the PCD5008 is reset, until the
corresponding FRS bit in the receiver line control packet is
set or the PCD5008 is turned on for the first time after a
reset (by setting the ON bit in the control packet). This
allows the designer to force the receiver control lines to the
receiver off setting with external pull-up or pull-down
resistors before the host can configure these settings in
the PCD5008.
8.5.4
R
ECEIVER OFF STATE
(ID = 10H)
The receiver off state is configured by the receiver off
setting packet (Table 13), which defines the settings to be
applied when the PCD5008 decides to switch the
receiver off.
LBC:
low battery check (Table 13). If this bit is set, the
PCD5008 checks the status of the LOBAT port just before
leaving the receiver off state. Value after reset = 0.
CLS:
control line setting (Table 13). This is the value to be
output on the receiver control lines for the receiver off
state. Value after reset = 0.
ST:
step time (Table 13). This sets the duration of the
warm-up off time. The setting is in steps of 625
μ
s. Valid
values are 625
μ
s (ST = 01H) to 159.375 ms (ST = FFH).
Value after reset = 01H.
Table 12
Status packet bit assignments
Table 13
Receiver off setting packet bit assignments
BYTE
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
3
2
1
0
0
1
f
6
LB
LBU
1
f
5
x
x
1
f
4
x
1
f
3
c
3
x
1
f
2
c
2
1
f
1
c
1
x
1
f
0
c
0
FIV
SM
SMU
MT
EOF
BOE
BYTE
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
3
2
1
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
LBC
CLS
3
ST
3
CLS
7
ST
7
CLS
6
ST
6
CLS
5
ST
5
CLS
4
ST
4
CLS
2
ST
2
CLS
1
ST
1
CLS
0
ST
0
相關PDF資料
PDF描述
PCD5013 FLEX roaming decoder II
PCD5013H FLEX roaming decoder II
PCD5032 ADPCM CODEC for digital cordless telephones
PCD5032H ADPCM CODEC for digital cordless telephones
PCD5032T ADPCM CODEC for digital cordless telephones
相關代理商/技術參數
參數描述
PCD5008HBD-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication Decoder
PCD5013 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:FLEX roaming decoder II
PCD5013H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:FLEX roaming decoder II
PCD5032 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
PCD5032B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*