- 您現在的位置：買賣IC網 > PDF目錄299576 > OR3T125-4B432 FPGA, 784 CLBS, 92000 GATES, PBGA432 PDF資料下載
參數資料
| 型號： | OR3T125-4B432 |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 784 CLBS, 92000 GATES, PBGA432 |
| 封裝： | BGA-432 |
| 文件頁數： | 147/210頁 |
| 文件大?。?/td> | 2138K |
| 代理商： | OR3T125-4B432 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁當前第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
Lucent Technologies Inc.
41
Preliminary Data Sheet, Rev. 1
September 1998
ORCA Series 3 FPGAs
Programmable Input/Output Cells
(continued)
PIC Routing Resources
The PIC routing borrows many of the concepts and
constructs from the PLC routing. It is designed to be
able to gather an 8-bit bidirectional bus from any eight
consecutive I/O pads and route them to either or both
of the two adjacent PLCs. The eight I/O bits do not
need to start at a PIC boundary; that is, they may start
at one of the middle two PIOs in a PIC and span three
PICs.
Substantial routing has been added to the PIC to off-
load PLC routing from being used to move signals
around the PLC array perimeter. This saves PLC rout-
ing for logic purposes and provides greater flexibility for
locking design pinouts prior to final placement and rout-
ing of the device, or allowing a change in the pinout
late in the design cycle. The PIC routing has also been
increased substantially to allow routing to the complex
PIO cells that now allow multiple inputs and outputs per
device pin, along with new sequential control signals,
such as clock enable, LSR, and clock.
PICs are grouped in pairs for purposes of discussing
PIC routing. On the sides of a device, the PICs in a pair
are referred to as top and bottom. On the top or bottom
of a device, the PICs in a pair are referred to as left or
right. For example, on the top edge of the device, the
leftmost PIC, PT1, is the left PIC of a pair, and PIC PT2
is the right PIC of that pair. The next PIC to the right,
PT3, is the left PIC of the next pair, and so on.
The need for PIC pairs stems from the routing of
switching segments and PLC half- and long-line driv-
ers. As described below, the connectivity for these
types of routing is grouped across pairs of PICs to pro-
vide complete and fast routing of I/O signals between a
given PIC and the three adjacent PLCs: one orthogonal
and two diagonal.
PIC routing segments use the same terminology as
PLC routing segments, but are prefixed with a p to dis-
tinguish them as belonging to the PICs.
PIC Switching Segments. Each PIC has two groups
of switching segments (pSW), each group having eight
lines with connectivity to the PIOs in groups of four.
One set of switching segments connects to the PIC to
the left (above), and the other set connects to the
switching segments of the PIC to the right (below). This
means of connectivity between PICs using staggered
connections of groups of switching segments allows a
given PIC to route signals to both adjacent PICs and all
adjacent PLCs efficiently. This provides single signal
routing flexibility and routing of multiple buses on
groups of I/Os without tying up global routing
resources.
px1 Routing Segments. There are five px1 routing
segments in each PIC that run parallel to the edge of
the chip on which the PIC resides, each broken by a
CIP in each PIC. The px1 segments have connectivity
to the pSW segments and to the x1 routing segments
of the two adjacent PLCs.
px2 Routing Segments. There are five px2 routing
segments in each PIC that run parallel to the edge of
the chip on which the PIC resides. To provide greater
routing flexibility, the CIPs that break the px2 segments
every two PICs are staggered across the two PICs in a
pair. One PIC of the pair has break CIPs on the even
numbered px2 segments, and the other has them on
the odd numbered px2 segments. The px2 segments
have connectivity to the pSW segments and to the x1
routing segments of the two adjacent PLCs.
px5 Routing Segments. There are ten px5 routing
segments in each PIC that run parallel to the edge of
the chip on which the PIC resides. Two of the ten seg-
ments are broken in each PIC so that each segment is
broken every five PICs. All ten px5 segments break at
the corners of the chip, allowing independent px5 rout-
ing on each edge of the chip. The px5 routing seg-
ments connect to the pSW segments and the x5 and
xH routing segments of the two adjacent PLCs.
pxH Routing Segments. Each PIC contains eight pxH
routing segments that run parallel to the edge of the
chip on which the PIC resides. The pxH segments
have connectivity with the xL, xH, and one set of xBID
routing segments in the immediately adjacent PLC.
pxL Routing Segments. There are ten pxL routing
segments in each PIC that run parallel to the edge of
the chip on which the PIC resides. Each of the xL lines
makes a connection to an xL line from the adjacent
PLC. PIC long lines (xL) can be used for global signal
distribution just as PLC xL lines can.
相關PDF資料 |
PDF描述 |
|---|---|
| OR3T125-4B600 | FPGA, 784 CLBS, 92000 GATES, PBGA600 |
| OR3T125-4BA352I | FPGA, 784 CLBS, 92000 GATES, PBGA352 |
| OR3T125-4BA352 | FPGA, 784 CLBS, 92000 GATES, PBGA352 |
| OR3T125-5B432 | FPGA, 784 CLBS, 92000 GATES, PBGA432 |
| OR3T125-5B600 | FPGA, 784 CLBS, 92000 GATES, PBGA600 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OR3T125-4BC432I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T125-4BC600I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T125-4PS208I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T125-4PS240I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T125-5BA352 | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。