參數資料
型號： OCX160-PPT
廠商： Electronic Theatre Controls, Inc.
英文描述： OCX160 Crosspoint Switch
中文描述： OCX160交叉點開關
文件頁數： 14/44頁
文件大?。?/td> 710K
代理商： OCX160-PPT
OCX160 Crosspoint Switch
—
Preliminary Data Sheet
14
[Rev. 1.6] 2/20/01
I-Cube, Inc.
1.4
JTAG Configuration Controller
The Output port attributes and the Switch Matrix connections can be programmed using the JTAG serial
bus. The RapidConfigure Interface can be enabled or disabled using the JTAG serial bus.
The JTAG
–
based serial mode is always available for configuration regardless of whether the
RapidConfigure mode is enabled or disabled. However, proper care must be taken when switching between
JTAG and RapidConfigure for configuring the devices. Before attempting to change Switch Matrix
connections or output port configuration through JTAG, the user must first ensure that the RapidConfigure
mode is disabled by using JTAG serial mode to set the RCE bit to zero in the Mode Control Register.
1.4.1
JTAG Interface
The dedicated JTAG TAP interface is designed in compliance with the IEEE-1149.1. The standard
interface has five pins: Test Data Out (TDO), Test Mode Select (TMS), Test Data In (TDI), Test
Reset (TRST#), and Test Clock (TCK), which allow Boundary Scan Testing as well as device
configuration and verification. The I-Cube supplied software will automatically generate the
necessary bitstream from a higher-level textual description of the required configuration. Data on
the TDI and TMS pins are clocked into the device on the rising edge of the TCK signal, while the
valid data appears on the TDO pin after the falling edge of TCK. For more detailed information
on JTAG programming, refer to the
OCX160 Register Programming Manual
.
1.4.2
Output Port Configuration
Output port configuration is accomplished by loading the appropriate bitstream into the
programming registers present at each Output port. The JTAG serial bus is used to load
configuration data into the Output port programming registers, one Output port at a time.
1.4.3
Switch Matrix Configuration
The contents of the SRAM cells controlling Switch Matrix connection can be modified using the
JTAG. This is accomplished by loading the configuration data, one word at a time, into the SRAM
cells in the Switch Matrix.
1.4.4
Mode Control Register Configuration
The OCX160 contains a single bit Mode Control Register used to store user flags for
RapidConfigure Enable (RCE). These are required for proper functioning of the device. The
contents of this register can be changed using the JTAG interface and a special JTAG instruction.
Table 6
Mode Control Register
RCE
Mode
0
RapidConfigure interface disabled (OFF)
1
RapidConfigure interface enabled (ON)
相關PDF資料
PDF描述
OD-880F1 HIGH POWER GAAIAS IR EMITTERS
OD880F1 HIGH POWER GAAIAS IR EMITTERS
OD880F HIGH POWER GAAIAS IR EMITTERS
OD-880F HIGH POWER GAAIAS IR EMITTERS
OD-A8HT18CS Precision SC-cut OCXO in 20x20 mm Through Hole Package
相關代理商/技術參數
參數描述
OC-X87XXXXX 制造商:NEL 制造商全稱:Nel Frequency Controls,inc 功能描述:Micro-miniature OCXO
OCXO 制造商:TEMEX 制造商全稱:TEMEX 功能描述:Space qualified OCXO - Oven Controlled Crystal Oscillator, Flat pack General Specification (rev1)
OCXO-131A 制造商:KSS 制造商全稱:KSS 功能描述:Oven Controlled Crystal Oscillator
OCXO-131A1 制造商:KSS 制造商全稱:KSS 功能描述:Oven Controlled Crystal Oscillator
OCXO-20 制造商:PETERMANN 制造商全稱:PETERMANN 功能描述:HIGH RELIABILITY FOR LOW COST AGING OF +-0.001 PPM/DAY IN SMALL PACKAGE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*