- 您現在的位置：買賣IC網 > PDF目錄384775 > OCX160-PPT (Electronic Theatre Controls, Inc.) OCX160 Crosspoint Switch PDF資料下載
參數資料
| 型號： | OCX160-PPT |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | OCX160 Crosspoint Switch |
| 中文描述： | OCX160交叉點開關 |
| 文件頁數： | 11/44頁 |
| 文件大小： | 710K |
| 代理商： | OCX160-PPT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
OCX160 Crosspoint Switch
—
Preliminary Data Sheet
I-Cube, Inc.
[Rev. 1.6] 2/20/01
11
1.3
RapidConfigure Interface
RapidConfigure (RC) is a 25 signal parallel interface that is used to program the OCX160 device. The 25
pins are allocated as follows:
RCA[6:0] = RapidConfigure Address A. RCA are input pins.
RCB[6:0] = RapidConfigure Address B. RCB are input pins.
RCI[3:0] = RapidConfigure Instruction Bits
RCO[4:0] = RapidConfigure Readback. RCO are output pins.
RC_CLK#= RapidConfigure Clock (negative edge clock)
RC_EN# = RapidConfigure Cycle Enable (active low)
1.3.1
RapidConfigure Programming Instructions
The RC interface supports both write and read types of operations:
1.
Write Operations (reset crosspoint and Input or Output Buffer (IOB), configure an
Output Buffer, connect/disconnect crosspoint)
2.
Read Operations (Output Buffer and crosspoint configuration read).
Table 3
RapidConfigure Programming Instructions
RCI[3:0]
RCA[6:0]
RCB[6:0]
RCO[4:0]
Instruction
Description
0000
Reserved
0001
Reserved
0010
X
X
Reset Crosspoint
Array
Reset the entire crosspoint array to no
connect. All Output Buffers remain
unchanged by this operation.
0011
X
Input Port
Address
Set Array to Broadcast
mode
Connects the input selected by RCB[6:0]
to all output ports and disconnects all
other inputs. The Global Update
(UPDATE#) pin must be held high
during Broadcast mode. Activating the
Global Update pin returns the array to
the previous program condition.
0100
Output Port
Address
Data
Configure an Output
Buffer
Program an Output Buffer specified by
RCA[6:0].
See Table 5 for RCB[6:0] bit assignment
and buffer functionality.
0101
Readback Crosspoint,
Output Buffer status
This is a two-cycle instruction.
Cycle 1
Output Port
Address
Intput Port
Address
X
Specify the crosspoint connect status at
input location specified by RCA[6:0] to
the output location specified by
RCB[6:0].
相關PDF資料 |
PDF描述 |
|---|---|
| OD-880F1 | HIGH POWER GAAIAS IR EMITTERS |
| OD880F1 | HIGH POWER GAAIAS IR EMITTERS |
| OD880F | HIGH POWER GAAIAS IR EMITTERS |
| OD-880F | HIGH POWER GAAIAS IR EMITTERS |
| OD-A8HT18CS | Precision SC-cut OCXO in 20x20 mm Through Hole Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OC-X87XXXXX | 制造商:NEL 制造商全稱:Nel Frequency Controls,inc 功能描述:Micro-miniature OCXO |
| OCXO | 制造商:TEMEX 制造商全稱:TEMEX 功能描述:Space qualified OCXO - Oven Controlled Crystal Oscillator, Flat pack General Specification (rev1) |
| OCXO-131A | 制造商:KSS 制造商全稱:KSS 功能描述:Oven Controlled Crystal Oscillator |
| OCXO-131A1 | 制造商:KSS 制造商全稱:KSS 功能描述:Oven Controlled Crystal Oscillator |
| OCXO-20 | 制造商:PETERMANN 制造商全稱:PETERMANN 功能描述:HIGH RELIABILITY FOR LOW COST AGING OF +-0.001 PPM/DAY IN SMALL PACKAGE |
發布緊急采購，3分鐘左右您將得到回復。