- 您現在的位置：買賣IC網 > PDF目錄1956 > NCN6004AFTBR2G (ON Semiconductor)IC INTERFACE SAM/SIM DUAL 48TQFP PDF資料下載
參數資料
| 型號： | NCN6004AFTBR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 27/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE SAM/SIM DUAL 48TQFP |
| 標準包裝： | 1 |
| 應用： | PC，PDA |
| 接口： | 微控制器 |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 封裝/外殼： | 48-TQFP 裸露焊盤 |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | NCN6004AFTBR2GOSDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
NCN6004A
http://onsemi.com
33
NOTE:
Both sides of the interface run with open drain load
(worst case condition)
Figure 34. Typical I/O Rise and Fall Time
ESD Protection
The NCN6004A includes silicon devices to protect the
pins against the ESD spikes voltages. To cope with the
different ESD voltages developed across these pins, the built
in structures have been designed to handle either 2 kV, when
related to the microcontroller side, or 8 kV when connected
with the external contacts. Practically, the CRD_RST,
CRD_CLK, CRD_IO, CRD_C4 and CRD_C8 (both A and
B sections) pins can sustain 8 kV, the maximum short circuit
current being limited to 15 mA. The CRD_VCC_A and
CRD_VCC_B pins have the same ESD protection, but can
source up to 65 mA continuously each, the absolute
maximum current being 150 mA per section.
Security Features
In order to protect both the interface and the external smart
card, the NCN6004A provides security features to prevent
catastrophic failures as depicted here after.
Pin Current Limitation: in case of a short circuit to
ground, the current forced by the device is limited to 10 mA
for any pins, except CRD_CLK_A and CRD_CLK_B pins
which are both limited to 70 mA. No feedback is provided
to the external MPU.
DC/DC Operation: The internal circuit continuously
senses the CRD_VCC_A and CRD_VCC_B voltages and,
in the case of either over or under voltage situation, update
the STATUS register accordingly. This register can be read
out by the MPU but no interrupts are activated.
DC/DC Overload: When an overload is sensed across the
CRD_VCC_A or CRD_VCC_B output, during either the
power on sequence or when the system was previously
running, the NCN6004A generates an interrupt by pulling
down the INT pin. It is up to the microcontroller to identify
the origin of the overload by reading the STATUS pin
accordingly.
Battery Voltage: Both the Positive going and the
Negative going voltage are detected by the NCN6004A, a
POWER_DOWN sequence and the STATUS register being
updated accordingly. The external MPU can read the
STATUS pin to take whatever is appropriate to cope with the
situation. The NCN6004A does not provide any further
internal voltage regulation.
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
| NCN8024RDWR2G | IC SMART CARD IC2 28SOIC |
| NCN8025MTTBG | IC SMART CARD I2C 16-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6010 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010DTB | 功能描述:轉換 - 電壓電平 2.7V Sim Card RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
發布緊急采購，3分鐘左右您將得到回復。