- 您現在的位置：買賣IC網 > PDF目錄385641 > MTB50P03HDL (ON SEMICONDUCTOR) Power MOSFET 50 Amps, 30 Volts, Logic Level(50A, 30V, D2PAK, P溝道功率MOSFET) PDF資料下載
參數資料
| 型號： | MTB50P03HDL |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 功率晶體管 |
| 英文描述： | Power MOSFET 50 Amps, 30 Volts, Logic Level(50A, 30V, D2PAK, P溝道功率MOSFET) |
| 中文描述： | 50 A, 30 V, 0.025 ohm, P-CHANNEL, Si, POWER, MOSFET |
| 封裝： | CASE 418B-04, D2PAK-3 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 94K |
| 代理商： | MTB50P03HDL |
MTB50P03HDL
http://onsemi.com
10
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones,
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 19 shows a typical heating
profile for use when soldering a surface mount device to a
printed circuit board. This profile will vary among
soldering systems but it is a good starting point. Factors that
can affect the profile include the type of soldering system in
use, density and types of components on the board, type of
solder used, and the type of board or substrate material
being used. This profile shows temperature versus time.
The line on the graph shows the actual temperature that
might be experienced on the surface of a test board at or
near a central solder joint. The two profiles are based on a
high density and a low density board. The Vitronics
SMD310 convection/infrared reflow soldering system was
used to generate this profile. The type of solder used was
62/36/2 Tin Lead Silver with a melting point between
177–189
°
C. When this type of furnace is used for solder
reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
5
°
C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER
JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
170
°
C
140
°
C
Figure 19. Typical Solder Heating Profile
相關PDF資料 |
PDF描述 |
|---|---|
| MTD20N06HDLT4 | Power MOSFET 20 Amps, 60 Volts, Logic Level N−Channel DPAK |
| MTD20N06HDLT4G | Power MOSFET 20 Amps, 60 Volts, Logic Level N−Channel DPAK |
| MTD6N15 | Power Field Effect Transistor DPAK for Surface Mount(功率場效應晶體管) |
| MTD6N20E | Power MOSFET 6 Amps, 200 Volts(6A, 200V功率MOSFET) |
| MTG-12864A | MTG-12864A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MTB50P03HDLG | 功能描述:MOSFET PFET 30V 50A RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| MTB50P03HDLT4 | 功能描述:MOSFET 30V 50A Logic Level RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| MTB50P03HDLT4G | 功能描述:MOSFET PFET D2PAK 30V 50A 25mOhm RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| MTB50SA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Full-Size (7.3mm or 4.7mm height) |
| MTB50SAM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Full-Size (7.3mm or 4.7mm height) |
發布緊急采購，3分鐘左右您將得到回復。