參數資料
型號： MT9044AP
廠商： Mitel Networks Corporation
英文描述： T1/E1/OC3 System Synchronizer
中文描述： T1/E1/OC3系統同步
文件頁數： 5/30頁
文件大?。?/td> 120K
代理商： MT9044AP
Advance Information
MT9044
5
Functional Description
The MT9044 is a Multitrunk System Synchronizer,
providing timing (clock) and synchronization (frame)
signals to interface circuits for T1 and E1 Primary
Rate Digital Transmission links.
Figure 1 shows the functional block diagram which is
described in the following sections.
Reference Select MUX Circuit
The MT9044 accepts two simultaneous reference
input signals and operates on their falling edges.
Either the primary reference (PRI) signal or the
secondary reference (SEC) signal can be selected
as input to the TIE Corrector Circuit. The selection is
based on the Control, Mode and Reference
Selection of the device. See Tables 1, 4 and 5.
Frequency Select MUX Circuit
The MT9044 operates with one of three possible
input reference frequencies (8kHz, 1.544MHz or
2.048MHz). The frequency select inputs (FS1 and
FS2) determine which of the three frequencies may
be used at the reference inputs (PRI and SEC). Both
inputs must have the same frequency applied to
them. A reset (RST) must be performed after every
frequency select input change. Operation with FS1
and FS2 both at logic low is reserved and must not
be used. See Table 1.
Table 1 - Input Frequency Selection
Time Interval Error (TIE) Corrector Circuit
The TIE corrector circuit, when enabled, prevents a
step change in phase on the input reference signals
(PRI or SEC) from causing a step change in phase at
the input of the DPLL block of Figure 1.
During reference input rearrangement, such as
during a switch from the primary reference (PRI) to
the secondary reference (SEC), a step change in
phase on the output signals will occur. A phase step
at the input of the DPLL will lead to unacceptable
phase changes in the output signal.
As shown in Figure 3, the TIE Corrector Circuit
receives one of the two reference (PRI or SEC)
signals, passes the signal through a programmable
delay line, and uses this delayed signal as an
internal virtual reference, which is input to the DPLL.
Therefore, the virtual reference is a delayed version
of the selected reference.
During a switch, from one reference to the other, the
State Machine first changes the mode of the device
FS2
FS1
Input Frequency
0
0
Reserved
0
1
8kHz
1
0
1.544MHz
1
1
2.048MHz
Figure 3 - TIE Corrector Circuit
Programmable
Delay Circuit
Control Signal
Delay Value
TCLR
Resets Delay
Compare
Circuit
TIE Corrector
Enable
from
State Machine
Control
Circuit
Feedback
Signal from
Frequency
Select MUX
PRI or SEC
from
Reference
Select Mux
Virtual
Reference
to DPLL
相關PDF資料
PDF描述
MT9045 T1/E1/OC3 System Synchronizer(T1/E1/OC3 系統同步裝置（由一個數字鎖相環組成）)
MT90710 High-Speed Isochronous Multiplexer
MT90710AP High-Speed Isochronous Multiplexer
MT9071 Quad T1/E1/J1 Transceiver(多端口 T1/E1/J1幀調節器（集成四個獨立幀調節器）)
MT9072 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
相關代理商/技術參數
參數描述
MT9044AP1 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:T1/E1/OC3 SYSTEM SYNCHRONIZER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 44PLCC 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 44PLCC
MT9044APR1 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Tape and Reel
MT9045 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/OC3 System Synchronizer
MT9045AN 制造商:Microsemi Corporation 功能描述:
MT9045AN1 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 3.3V 48SSOP - Rail/Tube 制造商:Microsemi Corporation 功能描述:T1/E1/OC3 SYSTEM SYNCHRONIZER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*