- 您現在的位置：買賣IC網 > PDF目錄384760 > MT9044AP (Mitel Networks Corporation) T1/E1/OC3 System Synchronizer PDF資料下載
參數資料
| 型號： | MT9044AP |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/OC3 System Synchronizer |
| 中文描述： | T1/E1/OC3系統同步 |
| 文件頁數： | 17/30頁 |
| 文件大?。?/td> | 120K |
| 代理商： | MT9044AP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Advance Information
MT9044
17
Figure 12 - Unsymmetrical Guard Time
Circuit
Figure 13 shows a typical timing example of an
unsymmetrical Guard Time Circuit with the MT9044
in Automatic Control.
TIE Correction (using GTi)
When Primary Holdover Mode is entered for short
time periods, TIE correction should not be enabled.
This will prevent unwanted accumulated phase
change between the input and output. This is mainly
applicable to Manual Control, since Automatic
Control together with the Guard Time Circuit
inherently operate in this manner.
For instance, 10 Normal to Holdover to Normal mode
change sequences occur, and in each case Holdover
was entered for 2s. Each mode change sequence
could account for a phase change as large as 350ns.
Thus, the accumulated phase change could be as
large as 3.5us, and, the overall MTIE could be as
large as 3.5us.
0.05ppm is the accuracy of Holdover Mode
50ns is the maximum phase continuity of the
MT9044 from Normal Mode to Holdover Mode
200ns is the maximum phase continuity of the
MT9044 from Holdover Mode to Normal Mode (with
or without TIE Corrector Circuit)
When 10 Normal to Holdover to Normal mode
change sequences occur without MTIE enabled, and
in each case holdover was entered for 2s, each
mode change sequence could still account for a
phase change as large as 350ns. However, there
would be no accumulated phase change, since the
input to output phase is re-aligned after every
Holdover to Normal state change. The overall MTIE
would only be 350ns.
R
P
1k
GTi
C
10uF
R
C
150k
MT9044
GTo
+
R
D
1k
Phasehold
Phasestate
Phase
10
0.05
ppm
2
s
×
100
ns
=
=
50
ns
200
ns
250
ns
=
+
=
10
250
ns
100
ns
+
(
)
×
3.5
us
=
=
Figure 13 - Automatic Control, Unsymmetrical Guard Time Circuit Timing Example
PRI
NORMAL
SEC
NORMAL
PRI
HOLDOVER
PRI
NORMAL
LOS2
GOOD
PRI
SIGNAL
STATUS
SEC
SIGNAL
STATUS
LOS1
PRI
NORMAL
PRI
HOLDOVER
BAD
GOOD
BAD
GOOD
GOOD
GTo
GTi
MT9044
STATE
V
SIH
NOTES:
1. T
D
represents the time delay from when the reference goes
bad to when the MT9044 is provided with a LOS indication.
T
D
T
D
相關PDF資料 |
PDF描述 |
|---|---|
| MT9045 | T1/E1/OC3 System Synchronizer(T1/E1/OC3 系統同步裝置（由一個數字鎖相環組成）) |
| MT90710 | High-Speed Isochronous Multiplexer |
| MT90710AP | High-Speed Isochronous Multiplexer |
| MT9071 | Quad T1/E1/J1 Transceiver(多端口 T1/E1/J1幀調節器（集成四個獨立幀調節器）) |
| MT9072 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9044AP1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:T1/E1/OC3 SYSTEM SYNCHRONIZER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 44PLCC 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 44PLCC |
| MT9044APR1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Tape and Reel |
| MT9045 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/OC3 System Synchronizer |
| MT9045AN | 制造商:Microsemi Corporation 功能描述: |
| MT9045AN1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 3.3V 48SSOP - Rail/Tube 制造商:Microsemi Corporation 功能描述:T1/E1/OC3 SYSTEM SYNCHRONIZER |
發布緊急采購，3分鐘左右您將得到回復。