- 您現在的位置：買賣IC網 > PDF目錄384755 > MT48LC4M32LFFC (Micron Technology, Inc.) SYNCHRONOUS DRAM PDF資料下載
參數資料
| 型號： | MT48LC4M32LFFC |
| 廠商： | Micron Technology, Inc. |
| 英文描述： | SYNCHRONOUS DRAM |
| 中文描述： | 同步DRAM |
| 文件頁數： | 34/52頁 |
| 文件大?。?/td> | 1281K |
| 代理商： | MT48LC4M32LFFC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
34
128Mb: x32 SDRAM
128MbSDRAMx32_D.p65 – Rev. D; Pub. 6/02
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2002, Micron Technology, Inc.
128Mb: x32
SDRAM
12. Other input signals are allowed to transition no
more than once in any two-clock period and are
otherwise at valid V
IH
or V
IL
levels.
13. I
DD
specifications are tested after the device is prop-
erly initialized.
14. Timing actually specified by
t
CKS; clock(s) speci-
fied as a reference only at minimum cycle rate.
15. Timing actually specified by
t
WR plus
t
RP; clock(s)
specified as a reference only at minimum cycle rate.
16. Timing actually specified by
t
WR.
17. Required clocks are specified by JEDEC function-
ality and are not dependent on any timing param-
eter.
18. The I
DD
current will decrease as the CAS latency is
reduced. This is due to the fact that the maximum
cycle rate is slower as the CAS latency is reduced.
19. Address transitions average one transition every
two clocks.
20. CLK must be toggled a minimum of two times dur-
ing this period.
21. Based on
t
CK = 143 MHz for -7, 166 MHz for -6.
22. V
IH
overshoot: V
IH
(MAX) = V
DD
Q + 1.2V for a pulse
width
≤
3ns, and the pulse width cannot be greater
than one third of the cycle rate. V
IL
undershoot: V
IL
(MIN) = -1.2V for a pulse width
≤
3ns, and the pulse
width cannot be greater than one third of the cycle
rate.
23. The clock frequency must remain constant during
access or precharge states (READ, WRITE, includ-
ing
t
WR, and PRECHARGE commands). CKE may
be used to reduce the data rate.
24. Auto precharge mode only.
25. JEDEC and PC100 specify three clocks.
26.
t
CK = 7ns for -7, 6ns for -6.
27. Check factory for availability of specially screened
devices having
t
WR = 10ns.
t
WR = 1
t
CK for 100 MHz
and slower (
t
CK = 10ns and higher) in manual
precharge.
NOTES
1.
All voltages referenced to V
SS
.
2.
This parameter is sampled. V
DD
, V
DD
Q = +3.3V;
f = 1 MHz, T
A
= 25°C; pin under test biased at 1.4V.
AC can range from 0pF to 6pF.
3.
I
DD
is dependent on output loading and cycle rates.
Specified values are obtained with minimum cycle
time and the outputs open.
4.
Enables on-chip refresh and address counters.
5.
The minimum specifications are used only to indi-
cate cycle time at which proper operation over the
full temperature range (0°C
≤
T
A
≤
+
70°C and
-40°C
≤
T
A
≤
+
85°C for IT parts) is ensured.
6.
An initial pause of 100μs is required after power-
up, followed by two AUTO REFRESH commands,
before proper device operation is ensured. (V
DD
and V
DD
Q must be powered up simultaneously. V
SS
and V
SS
Q must be at same potential.) The two
AUTO REFRESH command wake-ups should be
repeated any time the
t
REF refresh requirement is
exceeded.
7.
AC characteristics assume
t
T = 1ns.
8.
In addition to meeting the transition rate specifi-
cation, the clock and CKE must transit between V
IH
and V
IL
(or between V
IL
and V
IH
) in a monotonic
manner.
Q
9.
10.
t
HZ defines the time at which the output achieves
the open circuit condition; it is not a reference to
V
OH
or V
OL
. The last valid data element will meet
t
OH before going High-Z.
11. AC timing and I
DD
tests have V
IL
= .25 and V
IH
= 2.75,
with timing referenced to 1.5V crossover point.
Outputs measured at 1.5V with equivalent load:
30pF
相關PDF資料 |
PDF描述 |
|---|---|
| MT48LC64M8A2 | SYNCHRONOUS DRAM |
| MT48LC32M16A2 | SYNCHRONOUS DRAM |
| MT48LC8M16A2FB-75LIT | SYNCHRONOUS DRAM |
| MT48LC8M16A2FB-7E | SYNCHRONOUS DRAM |
| MT48LC8M16A2FB-7EIT | SYNCHRONOUS DRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT48LC4M32LFFC-10-REFURB | 制造商:Micron Technology Inc 功能描述: |
| MT48LC4M4A1 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC4M4A1TGS | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC4M4A2 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC64M4A2 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
發布緊急采購，3分鐘左右您將得到回復。