參數資料
型號： MT312
廠商： ZARLINK SEMICONDUCTOR INC
元件分類： 消費家電
英文描述： Satellite Channel Decoder
中文描述： SPECIALTY CONSUMER CIRCUIT, PQFP80
封裝： MQFP-80
文件頁數： 75/90頁
文件大?。?/td> 318K
代理商： MT312
Microprocessor Control
MT312
75
When the MT312 is powered up, the RESET pin 49 should be maintained low for typically 250ms (minimum
100ms) after VDD has reached normal operation levels. This is to ensure that the crystal oscillator and internal
PLL have become fully established and that the internal reset signal is fully clocked into all parts of the circuit.
As the reset pin is pulled high, the logic levels on ADDR[7:1] are latched to become the 2-wire bus address
ADDR[7:1]. ADDR[0] is the R/W bit.
IIN[5:1] are only used for test purposes and should be wired to VSS.
The circuit works as a slave transmitter with the eighth bit set high or as a slave receiver with the eighth bit set
low. In receive mode, the
fi
rst data byte is written to the RADD virtual register, which forms the register sub-
address.
Bit 7 of the RADD register, IAI is an Inhibit Auto Increment function. When the IAI bit is set high, the automatic
incrementing of register addresses is inhibited. IAI set low is the normal situation so that data bytes sent on the
2-wire bus after the RADD register data are loaded into successive registers. This automatic incrementing
feature avoids the need to individually address each register.
Following a valid chip address, the 2-wire bus STOP command resets the RADD register to 00. If the chip
address is not recognised, the MT312 will ignore all activity until a valid chip address is received. The 2-wire
bus START command does NOT reset the RADD register to 00. This allows a combined 2-wire bus message,
to point to a particular read register with a write command, followed immediately with a read data command. If
required, this could next be followed with a write command to continue from the latest address. RADD would
not be sent in this case. Finally a STOP command should be sent to free the bus.
When the 2-wire bus is addressed (after a recognised STOP command) with the read bit set, the
fi
rst byte read
out shall be the content of register 00.
11.4 Secondary 2-Wire Bus for Tuner Control
The MT312 has a General Purpose Port that can be con
fi
gured to provide a secondary 2-wire bus with full bi-
directional operation. When pass-through is enabled, a transparent connection is made to the tuner. This
innovative design simpli
fi
es the software required to program the tuner to only
fi
ve data bytes.
Pass-through mode is selected by setting register (20) GPP CTRL[B6] = 1.
The allocation of the pins is: GPP[0] pin 44 = CLK2, GPP[1] pin 45 = DATA2.
ADDR[7]
ADDR[6]
ADDR[5]
ADDR[4]
ADDR[3]
ADDR[2]
ADDR[1]
VSS
VSS
VSS
VDD
VDD
VDD
VSS
相關PDF資料
PDF描述
MT312T-Y 2x4mm Rectangular LED Lamps
MT3371BN Wide Dynamic Range DTMF Receiver
MT3371BS Wide Dynamic Range DTMF Receiver
MT3371BNR Wide Dynamic Range DTMF Receiver
MT3371BSR1 Wide Dynamic Range DTMF Receiver
相關代理商/技術參數
參數描述
MT3-1203SI 制造商:VOLGEN 制造商全稱:VOLGEN 功能描述:3 WATT DC/DC CONVERTER, SIINGLE & MULTIIPLE OUTPUTS
MT3-1205SI 制造商:VOLGEN 制造商全稱:VOLGEN 功能描述:3 WATT DC/DC CONVERTER, SIINGLE & MULTIIPLE OUTPUTS
MT3-1212SI 制造商:VOLGEN 制造商全稱:VOLGEN 功能描述:3 WATT DC/DC CONVERTER, SIINGLE & MULTIIPLE OUTPUTS
MT3-1212WI 制造商:VOLGEN 制造商全稱:VOLGEN 功能描述:3 WATT DC/DC CONVERTER, SIINGLE & MULTIIPLE OUTPUTS
MT3-1215WI 制造商:VOLGEN 制造商全稱:VOLGEN 功能描述:3 WATT DC/DC CONVERTER, SIINGLE & MULTIIPLE OUTPUTS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*