Host reset configuration all" />
參數資料
型號： MSC8101VT1500F
廠商： Freescale Semiconductor
文件頁數： 52/104頁
文件大?。?/td> 0K
描述： IC DSP 16BIT 250MHZ 332-FCPBGA
標準包裝： 90
系列： StarCore
類型： SC140 內核
接口： 通信處理器模塊（CPM）
時鐘速率： 300MHz
非易失內存： 外部
芯片上RAM： 512kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.60V
工作溫度： -40°C ~ 75°C
安裝類型： 表面貼裝
封裝/外殼： 332-BFBGA，F(xiàn)CPBGA
供應商設備封裝： 332-FCBGA（17x17）
包裝： 托盤
AC Timings
MSC8101 Technical Data, Rev. 19
Freescale Semiconductor
2-11
2.6.4.3 Host Reset Configuration
Host reset configuration allows the host to program the reset configuration word via the Host port after PORESET is
deasserted, as described in the MSC8101 Reference Manual. The MSC8101 samples the signals described in Table
2-13 one the rising edge of PORESET when the signal is deasserted.
If HPE is sampled high, the host port is enabled. In this mode the RSTCONF pin must be pulled up. The device
extends the internal PORESET until the host programs the reset configuration word register. The host must write
four 8-bit half-words to the Host Reset Configuration Register address to program the reset configuration word,
which is 32 bits wide. For more information, see the MSC8101 Reference Manual. The reset configuration word is
programmed before the internal PLL and DLL in the MSC8101 are locked. The host must program it after the
rising edge of the PORESET input. In this mode, the host must have its own clock that does not depend on the
MSC8101 clock. After the PLL and DLL are locked, HRESET remains asserted for another 512 bus clocks and is
then released. The SRESET is released three bus clocks later (see Figure 2-7).
2.6.4.4 Hardware Reset Configuration
Hardware reset configuration is enabled if HPE is sampled low at the rising edge of PORESET. The value driven on
RSTCONF
while PORESET changes from assertion to deassertion determines the MSC8101 configuration. If
RSTCONF
is deasserted (driven high) while PORESET changes, the MSC8101 acts as a configuration slave. If
6
Delay from SPLL lock to SRESET deassertion
DLL enabled
— BCLK = 18 MHz
— BCLK = 75 MHz
DLL disabled
— BCLK = 18 MHz
— BCLK = 75 MHz
3588
/ BLCK
515
/ BLCK
199.33
47.84
28.61
6.87
μs
Note:
Value given for lowest possible CLKIN frequency 18 MHz to ensure proper initialization of reset sequence.
Figure 2-7.
Host Reset Configuration Timing
Table 2-14.
Reset Timing (Continued)
No.
Characteristics
Expression
Min
Max
Unit
PORESET
Internal
HRESET
Input
Output (I/O)
SRESET
Output (I/O)
HRESET/SRESET are
extended for 512/515 BUS
clocks, respectively, from PLL
and DLL lock
PLL locks after
800 SPLLMFCLKs and
DLL locks 3073 BUS clocks
after PLL is locked.
When DLL is disabled,
reset period is shortened by
DLL lock time.
RSTCONF, HPE
pins are sampled
HRM, BTM
Any time
Host programs
Word
MODCK_H bits
are ready for PLL.
MODCK[1–3] pins
are sampled.
PORESET
Reset Configuration
1
2
3
5
4
6
asserted for
min 16
CLKIN.
PLL locked
DLL locked
相關PDF資料
PDF描述
MSC8103M1200F DSP 16BIT 300MHZ CPM 332-FCPBGA
MSC8103VT1200F IC DSP 16BIT 300MHZ 332-FCPBGA
MSC8112TVT2400V DSP DUAL CORE 431-FCPBGA
MSC8113TVT4800V DSP TRI-CORE 431-FCPBGA
MSC8122MP8000 DSP 16BIT 500MHZ MULTI 431FCPBGA
相關代理商/技術參數
參數描述
MSC8102 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core 16-Bit Digital Signal Processor
MSC81020 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:RF & MICROWAVE TRANSISTORS GENERAL PURPOSE AMPLIFIER APPLICATIONS
MSC8102M4000 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core 16-Bit Digital Signal Processor
MSC8102M4400 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core 16-Bit Digital Signal Processor
MSC8102RM 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core 16-Bit Digital Signal Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*