- 您現在的位置：買賣IC網 > PDF目錄45387 > MSC1202Y3RHHT (TEXAS INSTRUMENTS INC) 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36 PDF資料下載
參數資料
| 型號： | MSC1202Y3RHHT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36 |
| 封裝： | GREEN, PLASTIC, QFN-36 |
| 文件頁數： | 48/93頁 |
| 文件大?。?/td> | 1093K |
| 代理商： | MSC1202Y3RHHT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁
MSC1200
MSC1201
MSC1202
SBAS317E APRIL 2004 REVISED MAY 2006
www.ti.com
52
Configuration Address (CADDR) (write-only)
7
6
5
4
3
2
1
0
Reset Value
SFR 93h
00h
CADDR
Configuration Address. This register supplies the address for reading bytes in the 128 bytes of Flash Configuration
bits 70
Memory. It is recommended that faddr_data_read be used when accessing Configuration memory.This register is
also used as the address for the sfr_read and sfr_write routines, so it must be set prior to their use.
CAUTION: If this register is written to while executing from Flash Memory, the CDATA register will be incorrect.
Configuration Data (CDATA) (read-only)
7
6
5
4
3
2
1
0
Reset Value
SFR 94h
00h
CDATA
Configuration Data. This register will contain the data in the 128 bytes of Flash Configuration Memory that
bits 70
is located at the last written address in the CADDR register. This is a read-only register.
Serial Port 0 Control (SCON0)
7
6
5
4
3
2
1
0
Reset Value
SFR 98h
SM0_0
SM1_0
SM2_0
REN_0
TB8_0
RB8_0
TI_0
RI_0
00h
SM02
Serial Port 0 Mode. These bits control the mode of serial Port 0. Modes 1, 2, and 3 have 1 start and 1 stop bit in
bits 75
addition to the 8 or 9 data bits.
MODE
SM0
SM1
SM2
FUNCTION
LENGTH
PERIOD
0
Synchronous
8 bits
12 pCLK(1)
0
1
Synchronous
8 bits
4 pCLK(1)
1
0
1
0
Asynchronous
10 bits
Timer 1 Baud Rate Equation
1
0
1
AsynchronousValid Stop Required(2)
10 bits
Timer 1 Baud Rate Equation
2
1
0
Asynchronous
11 bits
64 pCLK(1) (SMOD = 0)
32 pCLK(1) (SMOD = 1)
2
1
0
1
Asynchronous with Multiprocessor Communication
11 bits
64 pCLK(1) (SMOD = 0)
32 pCLK(1) (SMOD = 1)
3
1
0
Asynchronous
11 bits
Timer 1 Baud Rate Equation
3
1
Asynchronous with Multiprocessor Communication(3)
11 bits
Timer 1 Baud Rate Equation
(1) p
CLK will be equal to tCLK, except that pCLK will stop for Idle mode.
(2) RI_0 will only be activated when a valid STOP is received.
(3) RI_0 will not be activated if bit 9 = 0.
REN_0
Receive Enable. This bit enables/disables the serial Port 0 received shift register.
bit 4
0: Serial Port 0 reception disabled.
1: Serial Port 0 received enabled (modes 1, 2, and 3). Initiate synchronous reception (mode 0).
TB8_0
9th Transmission Bit State. This bit defines the state of the 9th transmission bit in serial Port 0 modes 2 and 3.
bit 3
RB8_0
9th Received Bit State. This bit identifies the state of the 9th reception bit of received data in serial Port 0 modes
bit 2
2 and 3. In serial port mode 1, when SM2_0 = 0, RB8_0 is the state of the stop bit. RB8_0 is not used in mode 0.
TI_0
Transmitter Interrupt Flag. This bit indicates that data in the serial Port 0 buffer has been completely shifted out. In serial
bit 1
port mode 0, TI_0 is set at the end of the 8th data bit. In all other modes, this bit is set at the end of the last data bit.
This bit must be manually cleared by software.
RI_0
Receiver Interrupt Flag. This bit indicates that a byte of data has been received in the serial Port 0 buffer. In serial
bit 0
port mode 0, RI_0 is set at the end of the 8th bit. In serial port mode 1, RI_0 is set after the last sample of the incoming
stop bit subject to the state of SM2_0. In modes 2 and 3, RI_0 is set after the last sample of RB8_0. This bit must
be manually cleared by software.
相關PDF資料 |
PDF描述 |
|---|---|
| MSC1202Y2RHHT | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36 |
| MSC1202Y3RHHRG4 | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36 |
| MSC1201Y3RHHR | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36 |
| MSC1201Y2RHHRG4 | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36 |
| MSC1202Y2RHHRG4 | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSC1202Y3RHHTG4 | 功能描述:模數轉換器 - ADC Precision ADC & DAC w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MSC1205 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:32-Bit Duplex Controller/Driver with Digital Dimming Function |
| MSC1208 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:23-bit x 2 Duplex Controller/Driver with Digital Dimming and Keyscan Function |
| MSC1209 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:42-Bit Vacuum Fluorescent Display Tube Driver with Digital Dimming Function |
| MSC1210 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision Analog-to-Digital Converter (ADC) with 8051 Microcontroller and Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。