- 您現在的位置：買賣IC網 > PDF目錄3914 > MM908E625ACEK (Freescale Semiconductor)IC HALF-BRIDGE QUAD 54-SOIC PDF資料下載
參數資料
| 型號： | MM908E625ACEK |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 32/49頁 |
| 文件大小： | 0K |
| 描述： | IC HALF-BRIDGE QUAD 54-SOIC |
| 標準包裝： | 26 |
| 應用： | 自動鏡像控制 |
| 核心處理器： | HC08 |
| 程序存儲器類型： | 閃存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 輸入/輸出數： | 13 |
| 電源電壓： | 8 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 54-BSSOP（0.295"，7.50mm 寬）裸露焊盤 |
| 包裝： | 管件 |
| 供應商設備封裝： | 54-SOICW-EP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
38
Freescale Semiconductor
908E625
FUNCTIONAL DEVICE OPERATION
FACTORY TRIMMING AND CALIBRATION
STOP Mode
During STOP mode the STOP mode regulator supplies a
regulated output voltage. The STOP mode regulator has a
very limited output current capability. The output voltage will
be lower than the output voltage of the main voltage
regulator.
FACTORY TRIMMING AND CALIBRATION
To enhance the ease-of-use of the 908E625, various
parameters (e.g. ICG trim value) are stored in the flash
memory of the device. The following flash memory locations
are reserved for this purpose and might have a value different
from the empty (0xFF) state:
0xFD80:0xFDDF Trim and Calibration Values
0xFFFE:0xFFFF Reset Vector
In the event the application uses these parameters, one
has to take care not to erase or override these values. If these
parameters are not used, these flash locations can be erased
and otherwise used.
Trim Values
Below the usage of the trim values located in the flash
memory is explained
Internal Clock Generator (ICG) Trim Value
The internal clock generator (ICG) module is used to
create a stable clock source for the microcontroller without
using any external components. The untrimmed frequency of
the low frequency base clock (IBASE), will vary as much as
±25 percent due to process, temperature, and voltage
dependencies. To compensate this dependencies a ICG trim
values is located at address $FDC2. After trimming the ICG
is a range of typ. ±2% (±3% max.) at nominal conditions
(filtered (100 nF) and stabilized (4,7
μF) VDD = 5.0 V,
TAMBIENT~25 °C) and will vary over temperature and voltage
(VDD) as indicated in the 68HC908EY16 datasheet.
To trim the ICG this values has to be copied to the ICG
Trim Register ICGTR at address $38 of the MCU.
Important The value has to copied after every reset.
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E624ACEW | IC SWITCH TRIPLE MCU/LIN 54-SOIC |
| 06FMN-BMTTR-A-TB | CONN FMN HSNG 6POS STAG REV SMD |
| 046232104103800+ | CONN FFC/FPC 4POS 1MM R/A SMD |
| 046232106103800 | CONN FFC/FPC 6POS 1MM R/A SMD |
| 046232106103800+ | CONN FFC/FPC 6POS 1MM R/A SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。