LOGIC COMMANDS AND REGISTERS Go to STOP Mo" />
參數資料
型號： MM908E625ACEK
廠商： Freescale Semiconductor
文件頁數： 30/49頁
文件大?。?/td> 0K
描述： IC HALF-BRIDGE QUAD 54-SOIC
標準包裝： 26
應用： 自動鏡像控制
核心處理器： HC08
程序存儲器類型： 閃存（16 kB）
控制器系列： 908E
RAM 容量： 512 x 8
接口： SCI，SPI
輸入/輸出數： 13
電源電壓： 8 V ~ 18 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 54-BSSOP（0.295"，7.50mm 寬）裸露焊盤
包裝： 管件
供應商設備封裝： 54-SOICW-EP
Analog Integrated Circuit Device Data
36
Freescale Semiconductor
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Go to STOP Mode Bit (GS)
This write-only bit instructs the 908E625 to power down
and go into Stop mode. Reset or CPU interrupt requests clear
the GS bit.
1 = Power down and go into Stop mode
0 = Not in STOP mode
SYSTEM STATUS REGISTER (SYSSTAT)
Hall-Effect Sensor Input Pin Over-current Flag Bit
(HP_OCF)
This read/write flag is set on an over-current condition at
one of the Hall-effect sensor input pins. Clear HP_OCF and
enable the output by writing a Logic [1] to the HP_OCF flag.
Reset clears the HP_OCF bit. Writing a Logic [0] to HP_OCF
has no effect.
1 = Over-current condition on Hall-effect sensor input
pin has occurred
0 = No over-current condition on Hall-effect sensor input
pin has occurred
LIN Current Limitation Bit (LINCL)
This read-only bit is set if the LIN transmitter operates in
current limitation region. Due to excessive power dissipation
in the transmitter, software is advised to turn the transmitter
off immediately.
1 = Transmitter operating in current limitation region
0 = Transmitter not operating in current limitation region
HVDD Output Over-current Flag Bit (HVDD_OCF)
This read/write flag is set on an over-current condition at
the HVDD pin. Clear HVDD_OCF and enable the output by
writing a Logic [1] to the HVDD_OCF Flag. Reset clears the
HVDD_OCF bit. Writing a Logic [0] to HVDD_OCF has no
effect.
1 = Over-current condition on HVDD has occurred
0 = No over-current condition on HVDD has occurred
High Side Over-current Flag Bit (HS_OCF)
This read/write flag is set on an over-current condition at
the high side driver. Clear HS_OCF and enable the high side
driver by writing a Logic [1] to HS_OCF. Reset clears the
HS_OCF bit. Writing a Logic [0] to HS_OCF has no effect.
1 = Over-current condition on high side drivers has
occurred
0 = No over-current condition on high side drivers has
occurred
Low Voltage Bit (LVF)
This read only bit is a copy of the LVF bit in the Interrupt
Flag Register.
1 = Low voltage condition has occurred
0 = No low voltage condition has occurred
High Voltage Sensor Bit (HVF)
This read-only bit is a copy of the HVF bit in the Interrupt
Flag Register.
1 = High voltage condition has occurred
0 = No high voltage condition has occurred
H-Bridge Over-current Flag Bit (HB_OCF)
This read / write flag is set on an over-current condition at
the H-Bridges. Clear HB_OCF and enable the H-Bridge
driver by writing a Logic [1] to HB_OCF. Reset clears the
HB_OCF bit. Writing a Logic [0] to HB_OCF has no effect.
1 = Over-current condition on H-Bridges has occurred
0 = No over-current condition on H-Bridges has
occurred
Over-temperature Status Bit (HTF)
This read-only bit is a copy of the HTF bit in the Interrupt
Flag Register.
1 = Over-temperature condition has occurred
0 = No over-temperature condition has occurred
AUTONOMOUS WATCHDOG (AWD)
The Autonomous Watchdog module consists of three
functions:
Watchdog function for the CPU in RUN mode
Periodic interrupt function in STOP mode
Cyclic wake-up function in STOP mode
The AWD is enabled if AWDIE, AWDRE, or AWDCC in the
AWDCTL Register is set. If these bits are cleared, the AWD
oscillator is disabled and the watchdog switched off.
WATCHDOG
The watchdog function is only available in RUN mode. On
setting the AWDRE bit, watchdog functionality in RUN mode
Table 11. LIN Slew Rate Selection Bits
SRS1
SRS0
LIN Slew Rate
0
Initial Slew Rate (20 kBaud)
0
1
Slow Slew Rate (10 kBaud)
1
0
High Speed II (8x)
1
High Speed I (4x)
Register Name and Address: SYSSTAT - $0c
Bits
7
6
5
4
3
2
1
0
Read
HP_
OCF
LINCL HVDD
_OCF
HS_
OCF
LVF
HVF
HB_
OCF
HTF
Write
Reset
0000
相關PDF資料
PDF描述
MM908E624ACEW IC SWITCH TRIPLE MCU/LIN 54-SOIC
06FMN-BMTTR-A-TB CONN FMN HSNG 6POS STAG REV SMD
046232104103800+ CONN FFC/FPC 4POS 1MM R/A SMD
046232106103800 CONN FFC/FPC 6POS 1MM R/A SMD
046232106103800+ CONN FFC/FPC 6POS 1MM R/A SMD
相關代理商/技術參數
參數描述
MM908E625ACPEK 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E626 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVDWB 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*