- 您現在的位置：買賣IC網 > PDF目錄25626 > MD80C52TXXX-25SCD (ATMEL CORP) 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MD80C52TXXX-25SCD |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40 |
| 封裝： | 0.600 INCH, CERAMIC, DIP-40 |
| 文件頁數： | 211/395頁 |
| 文件大小： | 9022K |
| 代理商： | MD80C52TXXX-25SCD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁當前第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁第287頁第288頁第289頁第290頁第291頁第292頁第293頁第294頁第295頁第296頁第297頁第298頁第299頁第300頁第301頁第302頁第303頁第304頁第305頁第306頁第307頁第308頁第309頁第310頁第311頁第312頁第313頁第314頁第315頁第316頁第317頁第318頁第319頁第320頁第321頁第322頁第323頁第324頁第325頁第326頁第327頁第328頁第329頁第330頁第331頁第332頁第333頁第334頁第335頁第336頁第337頁第338頁第339頁第340頁第341頁第342頁第343頁第344頁第345頁第346頁第347頁第348頁第349頁第350頁第351頁第352頁第353頁第354頁第355頁第356頁第357頁第358頁第359頁第360頁第361頁第362頁第363頁第364頁第365頁第366頁第367頁第368頁第369頁第370頁第371頁第372頁第373頁第374頁第375頁第376頁第377頁第378頁第379頁第380頁第381頁第382頁第383頁第384頁第385頁第386頁第387頁第388頁第389頁第390頁第391頁第392頁第393頁第394頁第395頁
289
ATmega64A [DATASHEET]
8160D–AVR–02/2013
As an alternative to using the RESET signal, PEN can be held low during Power-on Reset while SCK is set
to “0”. In this case, only the PEN value at Power-on Reset is important. If the programmer cannot guarantee
that SCK is held low during Power-up, the PEN method cannot be used. The device must be powered down
in order to commence normal operation when using this method.
2.
Wait for at least 20 ms and enable SPI Serial Programming by sending the Programming Enable serial
instruction to pin MOSI.
3.
The SPI Serial Programming instructions will not work if the communication is out of synchronization. When
in sync. the second byte (0x53), will echo back when issuing the third byte of the Programming Enable
instruction. Whether the echo is correct or not, all four bytes of the instruction must be transmitted. If the
0x53 did not echo back, give RESET a positive pulse and issue a new Programming Enable command.
4.
The Flash is programmed one page at a time. The Page size is found in Table 28-10 on page 278. The
memory page is loaded one byte at a time by supplying the 7 LSB of the address and data together with the
Load Program Memory Page instruction. To ensure correct loading of the page, the data low byte must be
loaded before data high byte is applied for given address. The Program Memory Page is stored by loading
the Write Program Memory Page instruction with the 8 MSB of the address. If polling is not used, the user
must wait at least t
WD_FLASH before issuing the next page. (See Table 28-14). Accessing the SPI Serial Pro-
gramming interface before the Flash write operation completes can result in incorrect programming.
5.
The EEPROM array is programmed one byte at a time by supplying the address and data together with the
appropriate Write instruction. An EEPROM memory location is first automatically erased before new data is
written. If polling is not used, the user must wait at least t
WD_EEPROM before issuing the next byte. (See Table
28-14).
6.
Any memory location can be verified by using the Read instruction which returns the content at the selected
address at serial output MISO.
7.
At the end of the programming session, RESET can be set high to commence normal operation.
8.
Power-off sequence (if needed):
Set RESET to “1”.
Turn V
CC power off.
Note:
If other commands that polling (read) are applied before any write operation (FLASH, EEPROM, Lock bits, Fuses) is
completed, may result in incorrect programming.
28.8.2
Data Polling Flash
When a page is being programmed into the Flash, reading an address location within the page being programmed
will give the value 0xFF. At the time the device is ready for a new page, the programmed value will read correctly.
This is used to determine when the next page can be written. Note that the entire page is written simultaneously
and any address within the page can be used for polling. Data polling of the Flash will not work for the value 0xFF,
so when programming this value, the user will have to wait for at least t
WD_FLASH before programming the next
page. As a chip -erased device contains 0xFF in all locations, programming of addresses that are meant to contain
0xFF, can be skipped. See Table 28-14 for t
WD_FLASH value.
28.8.3
Data Polling EEPROM
When a new byte has been written and is being programmed into EEPROM, reading the address location being
programmed will give the value 0xFF. At the time the device is ready for a new byte, the programmed value will
read correctly. This is used to determine when the next byte can be written. This will not work for the value 0xFF,
but the user should have the following in mind: As a chip erased device contains 0xFF in all locations, program-
ming of addresses that are meant to contain 0xFF, can be skipped. This does not apply if the EEPROM is re-
相關PDF資料 |
PDF描述 |
|---|---|
| MD80C52CXXX-12SHXXX | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CDIP40 |
| MR80C52XXX-16P883 | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44 |
| MF280C51-12R | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP44 |
| M43C505F | 4-BIT, MROM, 2 MHz, MICROCONTROLLER |
| MQ80C32-20/883R | 8-BIT, 20 MHz, MICROCONTROLLER, CQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MD80C86 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MD80C862 | 制造商:Intel 功能描述:PROCESSOR:MICRO-PROCESSOR |
| MD80C86-2 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MD80C86-2/883 | 制造商:Intersil Corporation 功能描述:MPU 16BIT CMOS 8MHZ 40CDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:CPU 16BILT 5V CMOS 8MHZ 40CDIP - Bulk |
| MD80C86-2/B | 制造商:Intersil Corporation 功能描述:MPU 16BIT CMOS 8MHZ 40CDIP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。